REPLACEMENT
PROCEDURE
1. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH
Click here
2. REMOVE NO. 3 ENGINE UNDER COVER
Click here
3. REMOVE FRONT FENDER APRON SEAL LH
Click here
4. REPLACE AUTOMATIC TRANSAXLE FLUID
(a) Lift the vehicle. [#1]
NOTICE:
Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure the tilt angle from the front to rear of the vehicle is within +/- 1°).
(b) Remove the refill plug and gasket from the automatic transaxle case sub-assembly. [#2] |
|
(c) Using a T40 "TORX" socket wrench, remove the drain plug and O-ring from the transaxle housing. [#3] |
|
(d) Using a 17 mm straight hexagon wrench, remove the overflow plug and O-ring from the transaxle housing and drain the automatic transaxle fluid. [#4] |
|
(e) Measure the amount of automatic transaxle fluid drained. [#5] HINT: Add the same amount of automatic transaxle fluid in step [#8]. |
|
(f) Using a 17 mm straight hexagon wrench, install the overflow plug and a new O-ring to the transaxle housing. [#6] Torque: 47 N·m {479 kgf·cm, 35 ft·lbf} |
|
(g) Using a T40 "TORX" socket wrench, temporarily install the O-ring and drain plug to the transaxle housing. [#7] HINT: Reuse the old O-ring as the drain plug will be removed again to adjust the automatic transaxle fluid level. |
|
(h) Add automatic transaxle fluid to the refill hole using the same amount of automatic transaxle fluid drained in step [#5]. [#8] NOTICE: Use Toyota Genuine ATF WS. |
|
(i) Temporarily install the gasket and refill plug to avoid automatic transaxle fluid spillage. [#9] HINT: Reuse the old gasket as the refill plug will be removed again to adjust the automatic transaxle fluid level. |
|
(j) Lower the vehicle. [#10]
(k) Start the engine. [#11]
(l) Slowly move the shift lever from P to D, and then back to P. [#12]
HINT:
Slowly move the shift lever to circulate the automatic transaxle fluid through each part of the automatic transaxle assembly.
(m) Allow the engine to idle for 30 seconds to warm it up. [#13]
(n) Turn the engine switch off. [#14]
(o) Repeat steps [#1] to [#14].
(p) Repeat steps [#1] to [#10].
5. ADJUST AUTOMATIC TRANSAXLE FLUID TEMPERATURE (when Using the Techstream)
Click here
6. ADJUST AUTOMATIC TRANSAXLE FLUID TEMPERATURE (when Not Using the Techstream)
Click here
7. ADJUST AUTOMATIC TRANSAXLE FLUID LEVEL
Click here
8. REBUILD WORK
Click here
9. INSTALL FRONT FENDER APRON SEAL LH
Click here
10. INSTALL NO. 3 ENGINE UNDER COVER
Click here
11. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH
Click here
Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Power Tilt And Power Telescopic Steering Column System: Precaution
PRECAUTION PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE BATTERY TERMINAL NOTICE: When disconnecting the cable from the negative (-) battery terminal, initialize the following system(s) after the cable is reconnected. System See Procedure Lane Control System Pre-collision System ...
Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Transfer Case Front Oil Seal (for Lh Side): Replacement
REPLACEMENT CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transfer case oil seal removal/installation are shown below. Necessary Procedure After Parts Removed ...