Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual: Shift Solenoid "B" Circuit Short to Battery or Open (P075515)

Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual / Drivetrain / U881e (automatic Transmission / Transaxle) / Automatic Transaxle System / Shift Solenoid "B" Circuit Short to Battery or Open (P075515)

DESCRIPTION

Changing gears is performed by the ECM turning the shift solenoid valves SL1, SL2, SL3, SL4, SL5, S1 and S2 on and off.

If an open or short occurs in any of the shift solenoid valve circuits, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be driven. If all of the shift solenoid valves are malfunctioning, only the mechanical fluid pressure circuit will function and some manual operation will be possible. If an open or short occurs in a shift solenoid valve circuit, the ECM cuts power to the malfunctioning shift solenoid valve.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

Note

P075515

Shift Solenoid "B" Circuit Short to Battery or Open

1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other

  • Shift solenoid valve S2 is operated
  • Shift solenoid valve S2 circuit is short to +B or open
  • Malfunction status occurs 2 times per trip
  • 1-trip detection logic
  • Shift solenoid valve S2
  • Transmission wire
  • Harness and connector
  • ECM

Does not come on

DTC stored

SAE Code:

P0977

MONITOR DESCRIPTION

This DTC indicates an open or short to +B in the shift solenoid valve S2 circuit. When there is an open or short in any shift solenoid valve circuit, the ECM detects the problem, illuminates the MIL and stores a DTC.

When the shift solenoid valve S2 is off, if its resistance is 100 kΩ or more, the ECM determines there is an open or short to +B in the shift solenoid valve S2 circuit.

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

  1. Connect the Techstream to the DLC3.
  2. Turn the engine switch on (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the engine switch off and wait for 2 minutes or more.
  5. Turn the engine switch on (IG) and turn the Techstream on.
  6. Start the engine.
  7. Perform the D Position Shift Test inspection in Road Test.

    Click here

  8. Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
  9. Input the DTC: P075515.
  10. Check the DTC judgment result.

    Techstream Display

    Description

    NORMAL
    • DTC judgment completed
    • System normal

    ABNORMAL
    • DTC judgment completed
    • System abnormal

    INCOMPLETE
    • DTC judgment not completed
    • Perform driving pattern after confirming DTC enabling conditions

    N/A
    • Unable to perform DTC judgment
    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the judgment result shows INCOMPLETE or N/A, perform the confirmation driving pattern and check the DTC judgment result again.

WIRING DIAGRAM

Refer to DTC P075511.

Click here

CAUTION / NOTICE / HINT

NOTICE:

  • Perform the universal trip to clear permanent DTCs.

    Click here

  • Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

    Click here

PROCEDURE

1.

CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE (SHIFT SOLENOID VALVE S2) - ECM)

(a) Disconnect the D2 ECM connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

D2-77 (S2) - Body ground

20°C (68°F)

11 to 15 Ω
NG

GO TO STEP 3

OK

2.

REPLACE ECM

(a) Replace the ECM.

Click here

NEXT

PERFORM A/T CODE REGISTRATION

3.

CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

(a) Disconnect the D56 transmission wire connector.

(b) Disconnect the D2 ECM connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

D56-7 (SL) - D2-77 (S2)

Always

Below 1 Ω

D56-7 (SL) or D2-77 (S2) - Other terminals

Always

10 kΩ or higher
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)
OK

4.

INSPECT SHIFT SOLENOID VALVE S2

(a) Remove the shift solenoid valve S2.

Click here

*1

Shift Solenoid Valve S2

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

Shift solenoid valve S2 connector terminal - Shift solenoid valve S2 Body

20°C (68°F)

11 to 15 Ω

(c) Connect a positive (+) lead from the battery to the terminal of the solenoid valve connector, and a negative (-) lead to the solenoid body. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.

OK

REPAIR OR REPLACE TRANSMISSION WIRE

NG

REPLACE SHIFT SOLENOID VALVE S2

    Shift Solenoid "B" Circuit Short to Ground (P075511)
    DESCRIPTION Changing gears is performed by the ECM turning the shift solenoid valves SL1, SL2, SL3, SL4, SL5, S1 and S2 on and off. If an open or short occurs in any of the shift solenoid valve circui ...

    Pressure Control Solenoid "B" Circuit Open (P077513)
    DESCRIPTION Changing gears is performed by the ECM turning the shift solenoid valves SL1, SL2, SL3, SL4 and SL5 on and off. If an open or short occurs in any of the shift solenoid valve circuits, the ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Navigation System: "No GPS signal" mark is displayed
    CAUTION / NOTICE / HINT NOTICE: Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System. Click here PROCEDURE 1. CHECK CABIN (a) Check the cabin for a ...

    Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Park / Neutral Position Switch: On-vehicle Inspection
    ON-VEHICLE INSPECTION PROCEDURE 1. SECURE VEHICLE (a) Fully apply the parking brake and chock a wheel. CAUTION: Make sure to apply the parking brake and chock a wheel before performing this procedure. If the vehicle is not secure and the shift lever is moved to N, the vehicle may suddenly move, ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2024 Copyright www.lexusrx.net
    0.0192