Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual: Shift Solenoid "A" Actuator Stuck On (P07507E)

DESCRIPTION

Based on signals from the transmission revolution sensors (NT, NC3 and NC), the actual gear is detected.

The ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical malfunctions of the shift solenoid valves, transmission valve body assembly and automatic transaxle assembly (clutch, brake, gear, etc.).

Actual gear when shift solenoid valve S1 (without fail-safe control) malfunction occurs:

ECM commanded gear

1st

2nd

3rd

4th

5th

6th

7th

8th

*: Neutral

Actual gear during S1 stuck ON malfunction

1st

2nd

1st

4th

5th

6th

N*

8th

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

Note

P07507E

Shift Solenoid "A" Actuator Stuck On

1. Diagnosis Condition, 2. Malfunction Status, 3. Malfunction Time, 4. Other

  • Engine coolant temperature is 40°C (104°F) or higher, ATF temperature is -10°C (14°F) or higher, and the vehicle is being driven with the shift lever in D (no malfunctions are detected in the shift solenoid valves SL1, SL2, SL3, SL4, SL5 and S1, transmission revolution sensors (NT, NC3, NC), coolant temperature sensor, oil temperature sensor, knock control sensor, electronic throttle or CAN2)
  • When the ECM commands the transaxle to shift to 3rd or 7th gear, the engine overruns (neutral status).
  • Malfunction status continues for 0.6 seconds or more
  • 2-trip detection logic
  • Shift solenoid valve S1
  • Shift solenoid valve SLT
  • Shift solenoid valve SL1
  • Shift solenoid valve SL2
  • Shift solenoid valve SL3
  • Shift solenoid valve SL4
  • Transmission valve body assembly
  • Torque converter assembly
  • Automatic transaxle assembly (clutch, brake, gear, etc.)

Comes on

DTC stored

SAE Code:

P0752

MONITOR DESCRIPTION

The ECM commands gear shifts by turning the shift solenoid valves on and off. According to the input shaft revolution (speed), C3 clutch drum revolution (speed) and output shaft revolution (speed), the ECM detects the actual gear (1st, 2nd, 3rd, 4th, 5th, 6th, 7th or 8th gear). When the gear commanded by the ECM and the actual gear are not the same, the ECM illuminates the MIL and stores a DTC.

MONITOR STRATEGY

Related DTCs

P0752: Shift solenoid valve S1/ON malfunction

Required sensors/Components

Shift solenoid valve S1

Frequency of operation

Continuous

Duration

ON malfunction (A) and (B): 0.5 sec.

ON malfunction (C): 0.6 sec.

ON malfunction (D) and (E): Immediate

MIL operation

2 driving cycle

Sequence of operation

None

TYPICAL ENABLING CONDITIONS

All

The monitor will run whenever this DTC is not present.

(Not circuit malfunction)

P0717, P07BF, P07C0 (Turbine speed sensor circuit)

P07C1, P07C2, P2767 (Input speed sensor circuit)

P0793, P07C5, P07C6 (Intermediate shaft speed sensor circuit)

P0335, P0337, P0338 (Crankshaft Position Sensor "A" circuit) (This condition applies only if using fail-safe)

P0748 (Shift solenoid valve SL1 circuit)

P0778 (Shift solenoid valve SL2 circuit)

P0798 (Shift solenoid valve SL3 circuit)

P2810 (Shift solenoid valve SL4 circuit)

P2819 (Shift solenoid valve SL5 circuit)

P0973, P0974 (Shift solenoid valve S1 circuit)

P0115, P0117, P0118 (ECT sensor circuit)

P0712, P0713 (ATF temperature sensor circuit (TFT sensor))

P0327, P0328, P032C, P032D, P0332, P0333, P033C, P033D (KCS sensor circuit)

P0120, P0121, P0122, P0123, P0220, P0222, P0223, P0604, P0606, P0607, P060A, P060B, P060D, P060E, P0657, P1607, P2102, P2103, P2111, P2112, P2118, P2119, P2135 ((ETCS) Electronic throttle control system)

U0100 (CAN communication system)

NSW switch

"D" and "not R" and "not N"

Duration time from shifting "N" to "D"

4 sec. or more

ATF temperature

-10°C (14°F) or more

Engine

Starting

Fail-safe does not active due to following malfunctions:

 

Shift solenoid valve SL1

Not OFF or ON malfunction (P0746)

Shift solenoid valve SL2

Not OFF or ON malfunction (P0776)

Shift solenoid valve SL3

Not OFF or ON malfunction (P0796)

Shift solenoid valve SL4

Not OFF or ON malfunction (P2808)

Shift solenoid valve SL5

Not OFF or ON malfunction (P2817)

Shift solenoid valve S1

Not OFF or ON malfunction (P0751, P0752)

ON malfunction (A)
*1: Duration (0.5 sec.)

TCM selected gear

7th

Turbine speed/Input speed (NT/NC3)

Less than 1.9 or more than 2.0

Turbine speed - Output speed x 6th gear ratio

More than 50

Calculated load value

7.75% or more

Throttle valve opening angle

2% or more

TCM indicate pressure value of SL2

1600 kPa (16.3 kgf/cm2, 232 psi) or more

TCM indicate pressure value of SL3

330 kPa (3.4 kgf/cm2, 48 psi) or more

Count up time*1 stops when following conditions met: (a) or (b)

 

(a) Turbine speed / Output speed (NT / NO)

1.064 or more and 1.233 or less

(when output speed less than 600 rpm)

(b) Turbine speed - Output speed (NT - NO) x 5th gear ratio

-50 rpm or more and 50 rpm or less

(when output speed 600 rpm or more)

ON malfunction (B)

TCM selected gear

3rd

Output speed

330 rpm or more

Turbine speed/Input speed (NT/NC3)

Less than 1.9 or more than 2.0

Calculated load value

7.75% or more

Throttle valve opening angle

2% or more

TCM indicated pressure value of SL1

1600 kPa (16.3 kgf/cm2, 232 psi) or more

TCM indicated pressure value of SL3

1600 kPa (16.3 kgf/cm2, 232 psi) or more

ON malfunction (C)

TCM selected gear

3rd

Vehicle speed

3 km/h (1.87 mph) or more

Throttle valve opening angle

3% or more at engine speed 1000 rpm

(conditions vary with engine speed)

Calculated load value

7.75% or more

ECT

40°C (104°F) or more

Spark advance from MAX. retard timing by KCS control

0 °CA or more

ON malfunction (D)

TCM selected gear

3rd

ON malfunction (E)

TCM selected gear

7th

TYPICAL MALFUNCTION THRESHOLDS

When either conditions below is met: ON malfunction (A), (B), (C), (D) or (E)

ON malfunction (A)

Turbine speed - Output speed x 7th gear ratio (NT-NO x 7th gear)

400 rpm or more

ON malfunction (B)

Turbine speed - Output speed x 3rd gear ratio (NT-NO x 3rd gear)

400 rpm or more

ON malfunction (C)

When either condition below is met: (a) or (b)

 

(a) Turbine speed/Output speed (NT/NO)

4.197 or more and 8.529 or less

(When Output speed less than 130 rpm)

(b) Turbine speed - Output speed x 1st gear ratio

-50 rpm or more and 50 rpm or less

(When Output speed 130 rpm or more)

ON malfunction (D) and (E)

Shift solenoid valve SLT

ON malfunction

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.

HINT:

  • After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
  • When clearing the permanent DTCs, refer to the Clear Permanent DTC procedure.

    Click here

  1. Connect the Techstream to the DLC3.
  2. Turn the engine switch on (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the engine switch off and wait for 2 minutes or more.
  5. Turn the engine switch on (IG) and turn the Techstream on.
  6. Start the engine.
  7. Perform the D Position Shift Test inspection in Road Test. [*1]

    Click here

    HINT:

    [*1] : Normal judgment procedure.

    The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.

  8. Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
  9. Input the DTC: P07507E.
  10. Check the DTC judgment result.

    Techstream Display

    Description

    NORMAL

    • DTC judgment completed
    • System normal

    ABNORMAL

    • DTC judgment completed
    • System abnormal

    INCOMPLETE

    • DTC judgment not completed
    • Perform driving pattern after confirming DTC enabling conditions

    N/A

    • Unable to perform DTC judgment
    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.

CAUTION / NOTICE / HINT

NOTICE:

  • Perform the universal trip to clear permanent DTCs.

    Click here

  • Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

    Click here

PROCEDURE

1.

CHECK DTC OUTPUT (IN ADDITION TO DTC P07507E)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Powertrain / Transmission / Trouble Codes.

Powertrain > Transmission > Trouble Codes

(e) Read the DTCs using the Techstream.

Result

Proceed to

DTC P07507E and DTC P07457F, P07757F, P07957F, P27137F and/or P28077F are output

A

Only DTC P07507E is output

B

DTCs other than P07457F, P07507E, P07757F, P07957F, P27137F and P28077F are also output

C

HINT:

  • If any DTCs other than P07457F, P07507E, P07757F, P07957F, P27137F and P28077F are output, perform troubleshooting for those DTCs first.
  • If a shift solenoid valve is stuck ON or OFF, DTCs for several shift solenoid valves including the malfunctioning shift solenoid valve will be stored.
B

GO TO STEP 3

C

GO TO DTC CHART

A

2.

CLEAR DTC AND PERFORM STALL SPEED TEST

(a) Clear the DTCs.

Click here

HINT:

Write down the currently output DTCs before clearing them.

Powertrain > Transmission > Clear DTCs

(b) Perform the stall speed test.

Click here

Test Condition

Proceed to

Stall speed test can be performed

A

Stall speed test cannot be performed

B

B

GO TO STEP 5

A

3.

INSPECT SHIFT SOLENOID VALVE S1

(a) Remove the shift solenoid valve S1.

Click here

*1

Shift Solenoid Valve S1

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

Shift solenoid valve S1 connector terminal - Shift solenoid valve S1 body

20°C (68°F)

11 to 15 Ω

(c) Connect a positive (+) lead from the battery to the terminal of the solenoid valve connector, and a negative (-) lead to the solenoid body. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.

NG

REPLACE SHIFT SOLENOID VALVE S1

OK

4.

INSPECT SHIFT SOLENOID VALVE SL1, SL2, SL3 AND SL4

(a) Remove the shift solenoid valves SL1, SL2, SL3 and SL4.

Click here

*a

Component without harness connected

(Shift Solenoid Valve SL1, SL2, SL3 and SL4)

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

Shift solenoid valve SL1 connector terminal 1 - terminal 2

20°C (68°F)

5.0 to 5.6 Ω

Shift solenoid valve SL2 connector terminal 1 - terminal 2

20°C (68°F)

5.0 to 5.6 Ω

Shift solenoid valve SL3 connector terminal 1 - terminal 2

20°C (68°F)

5.0 to 5.6 Ω

Shift solenoid valve SL4 connector terminal 1 - terminal 2

20°C (68°F)

5.0 to 5.6 Ω

(c) Connect a positive (+) lead from the battery to terminal 1 and a negative (-) lead with a 21 W bulb to terminal 2 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.

NG

REPLACE SHIFT SOLENOID VALVE SL1, SL2, SL3 OR SL4

OK

5.

INSPECT SHIFT SOLENOID VALVE SLT

(a) Remove the shift solenoid valve SLT.

Click here

*a

Component without harness connected

(Shift Solenoid Valve SLT)

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

Shift solenoid valve SLT connector terminal 1 - terminal 2

20°C (68°F)

5.0 to 5.6 Ω

(c) Connect a positive (+) lead from the battery to terminal 1 and a negative (-) lead with a 21 W bulb to terminal 2 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.

NG

REPLACE SHIFT SOLENOID VALVE SLT

OK

6.

INSPECT TRANSMISSION VALVE BODY ASSEMBLY

(a) Inspect the transmission valve body assembly.

Click here

OK:

There is no foreign matter on each valve and they operate smoothly.

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

OK

7.

INSPECT TORQUE CONVERTER ASSEMBLY

(a) Inspect the torque converter assembly.

Click here

OK:

The torque converter assembly is normal.

NG

REPAIR OR REPLACE TORQUE CONVERTER ASSEMBLY

OK

8.

REPAIR OR REPLACE AUTOMATIC TRANSAXLE ASSEMBLY

(a) Repair or replace the automatic transaxle assembly.

Click here

NEXT

PERFORM A/T CODE REGISTRATION

    Shift Solenoid "A" Circuit Short to Battery or Open (P075015)
    DESCRIPTION Changing gears is performed by the ECM turning the shift solenoid valves SL1, SL2, SL3, SL4, SL5, S1 and S2 on and off. If an open or short occurs in any of the shift solenoid valve circui ...

    Shift Solenoid "A" Actuator Stuck Off (P07507F)
    DESCRIPTION Based on signals from the transmission revolution sensors (NT, NC3 and NC), the actual gear is detected. The ECM compares the actual gear with the shift schedule in the ECM memory to detec ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Window Defogger System: Parts Location
    PARTS LOCATION ILLUSTRATION *1 SEMICONDUCTOR PWR INTEGRATION ECU *2 ENGINE ROOM RELAY BLOCK ASSEMBLY - ALT FUSE *3 REAR WINDOW DEFOGGER WIRE (BACK WINDOW GLASS) - - ILLUSTRATION *1 REAR WINDOW DEFOGGER SWITCH *2 DLC3 *3 RADIO RECEIVER ASSEMBLY *4 AIR CONDIT ...

    Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Automatic Transaxle System: Transmission Fluid Temperature Sensor "A" Circuit Short to Battery or Open (P071015)
    DESCRIPTION The ATF temperature sensor converts the automatic transaxle fluid (ATF) temperature into a resistance value for use by the ECM. The ECM applies voltage to the temperature sensor through terminal THO1 of the ECM. The sensor resistance changes with the ATF temperature. As the temperature r ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2024 Copyright www.lexusrx.net
    0.0162