Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual: Speed Sensor
Components
COMPONENTS
ILLUSTRATION
.png)
| *1 | TRANSMISSION REVOLUTION SENSOR (NC3) | *2 | TRANSMISSION REVOLUTION SENSOR (NT) |
| *3 | TRANSMISSION REVOLUTION SENSOR (NC) | - | - |
.png) | Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | - | - |
Removal
REMOVAL
CAUTION / NOTICE / HINT
NOTICE:
Since the transmission revolution sensor (NC) is installed to the front planetary gear sub-assembly, it is necessary to disassemble the automatic transaxle before removing the transmission revolution sensor (NC). Refer to Automatic Transaxle Unit.
Click here .gif)
PROCEDURE
1. REMOVE TRANSMISSION VALVE BODY ASSEMBLY
Click here
2. REMOVE TRANSMISSION REVOLUTION SENSOR (NC3)
| (a) Disconnect the transmission revolution sensor (NC3) connector. |
|
.png)
| (b) Using a T30 "TORX" socket wrench, remove the bolt and transmission revolution sensor (NC3) from the automatic transaxle case sub-assembly. |
|
.png)
3. REMOVE TRANSMISSION REVOLUTION SENSOR (NT)
| (a) Remove the bolt and transmission revolution sensor (NT) from the automatic transaxle case sub-assembly. |
|
.png)
Installation
INSTALLATION
PROCEDURE
1. INSTALL TRANSMISSION REVOLUTION SENSOR (NT)
(a) Install the transmission revolution sensor (NT) to the automatic transaxle case sub-assembly with the bolt.
Torque:
5.4 N·m {55 kgf·cm, 48 in·lbf}
2. INSTALL TRANSMISSION REVOLUTION SENSOR (NC3)
(a) Using a T30 "TORX" socket wrench, install the transmission revolution sensor (NC3) to the automatic transaxle case sub-assembly with the bolt.
Torque:
5.4 N·m {55 kgf·cm, 48 in·lbf}
(b) Connect the transmission revolution sensor (NC3) connector.
3. INSTALL TRANSMISSION VALVE BODY ASSEMBLY
Click here .gif)
Installation
INSTALLATION PROCEDURE 1. INSTALL NO. 1 SWITCH WIRE HINT: Perform this procedure only when replacement of the No. 1 switch wire is necessary. (a) Engage the 6 clamps to install the No. 1 switch wire t ...
Torque Converter And Drive Plate
InspectionINSPECTION PROCEDURE 1. INSPECT TORQUE CONVERTER ASSEMBLY (a) Inspect the one-way clutch. (1) Press on the splines of the stator with a finger and rotate the spline. Check that the spline ro ...
Other materials:
Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Automatic Transaxle System: Shift Solenoid "B" Circuit Short to Battery or Open (P075515)
DESCRIPTION Changing gears is performed by the ECM turning the shift solenoid valves SL1, SL2, SL3, SL4, SL5, S1 and S2 on and off. If an open or short occurs in any of the shift solenoid valve circuits, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be driven. I ...
Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Rear Combination Light Assembly (w/o Rear No. 2 Seat): Installation
INSTALLATION CAUTION / NOTICE / HINT HINT:
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
PROCEDURE 1. INSTALL REAR COMBINATION LIGHT ASSEMBLY (a) Engage the grommet. (b) Engage the 3 guides and pin to temporarily install the rear combination ...
Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual
- For your information
- Pictorial index
- For safety and security
- Instrument cluster
- Operation of each component
- Driving
- Lexus Display Audio system
- Interior features
- Maintenance and care
- When trouble arises
- Vehicle specifications
- For owners
Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual
0.0164