Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual: Inspection

Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual / Engine & Hybrid System / 2gr-fks (emission Control) / Purge Valve / Inspection

INSPECTION

PROCEDURE

1. INSPECT PURGE VALVE (PURGE VSV) (for TMMC Made)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 - 2

20°C (68°F)

23 to 26 Ω

If the result is not as specified, replace the purge valve (purge VSV).

(b) Apply battery voltage between the terminals of the purge valve (purge VSV) and check that the following occurs when blowing air into the port (E).

OK:

Measurement Condition

Specified Condition

Battery voltage applied between terminals 1 and 2

Air flows from port (F)

Battery voltage not applied between terminals 1 and 2

Air does not flow

If the result is not as specified, replace the purge valve (purge VSV).

*a

Port (E)

*b

Port (F)

*c

Air

*d

Component without harness connected

(Purge Valve (Purge VSV))

2. INSPECT PURGE VALVE (PURGE VSV) (except TMMC Made)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 - 2

20°C (68°F)

23 to 26 Ω

If the result is not as specified, replace the purge valve (purge VSV).

(b) Apply battery voltage between the terminals of the purge valve (purge VSV) and check that the following occurs when blowing air into the port (E).

OK:

Measurement Condition

Specified Condition

Battery voltage applied between terminals 1 and 2

Air flows from port (F)

Battery voltage not applied between terminals 1 and 2

Air does not flow

If the result is not as specified, replace the purge valve (purge VSV).

*a

Port (E)

*b

Port (F)

*c

Air

*d

Component without harness connected

(Purge Valve (Purge VSV))
    Removal
    REMOVAL PROCEDURE 1. REMOVE V-BANK COVER SUB-ASSEMBLY Click here 2. REMOVE PURGE VALVE (PURGE VSV) (for TMMC Made) (a) Disconnect the purge valve (purge VSV) connector. *1 No. 1 F ...

    Installation
    INSTALLATION PROCEDURE 1. INSTALL PURGE VALVE (PURGE VSV) (for TMMC Made) (a) Install the purge valve (purge VSV) to the intake air surge tank assembly with the bolt. Torque: 21 N·m {214 kgf·cm, ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Rear Light Assembly: Removal
    REMOVAL CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH side and LH side. The following procedure is for the LH side. PROCEDURE 1. REMOVE BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY Click here 2. REMOVE REAR LIGHT ASSEMBLY (for Bulb Type Turn Signal Light) (a) Disconnect the ...

    Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Front Radar Sensor System: Precaution
    PRECAUTION PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE BATTERY TERMINAL NOTICE: When disconnecting the cable from the negative (-) battery terminal, initialize the following systems after the cable is reconnected. System Name See Procedure Lane Control System Pre-collision Sys ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2025 Copyright www.lexusrx.net
    0.0134