Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual: Components

*A

for TMC Made

*B

for TMMC Made

*1

NO. 1 ENGINE UNDER COVER

*2

NO. 2 ENGINE UNDER COVER

*3

NO. 3 ENGINE UNDER COVER

*4

FRONT FENDER APRON SEAL LH

*5

FRONT FENDER APRON SEAL RH

*6

FRONT FLOOR COVER LH

*7

FRONT WHEEL OPENING EXTENSION PAD LH

*8

FRONT WHEEL OPENING EXTENSION PAD RH

*9

FRONT LOWER BUMPER ABSORBER

-

-

*1

COOL AIR INTAKE DUCT SEAL

*2

INLET AIR CLEANER ASSEMBLY

*3

AIR CLEANER CAP WITH AIR CLEANER HOSE

*4

AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

*5

AIR CLEANER CASE SUB-ASSEMBLY

*6

AIR CLEANER BRACKET

*7

V-BANK COVER SUB-ASSEMBLY

*8

ECM

*9

NO. 1 FUEL VAPOR FEED HOSE

-

-

N*m (kgf*cm, ft.*lbf): Specified torque

-

-

*A

for 2WD

*B

for AWD

*C

for TMMC Made

*D

except TMMC Made

*1

TRANSMISSION CONTROL CABLE ASSEMBLY

*2

FUEL VAPOR FEED HOSE ASSEMBLY

*3

NO. 1 FUEL HOSE

*4

NO. 1 RADIATOR HOSE

*5

NO. 2 RADIATOR HOSE

*6

INLET HEATER WATER HOSE

*7

OUTLET HEATER WATER HOSE

*8

UNION TO CHECK VALVE HOSE

*9

NO. 1 TRANSMISSION OIL COOLER HOSE ASSEMBLY

*10

DISCHARGE HOSE SUB-ASSEMBLY

*11

SUCTION HOSE SUB-ASSEMBLY

*12

NO. 2 EARTH WIRE

*13

NO. 2 FUEL PIPE CLAMP

*14

NO. 2 FUEL TUBE SUB-ASSEMBLY

*15

FUEL TUBE SUB-ASSEMBLY

*16

O-RING

N*m (kgf*cm, ft.*lbf): Specified torque

●

Non-reusable part

Compressor oil ND-OIL 8 or equivalent

-

-

*A

w/ Suspension Tower Damper

-

-

*1

SUSPENSION TOWER DAMPER

-

-

N*m (kgf*cm, ft.*lbf): Specified torque

-

-

*1

FRONT STABILIZER BAR

*2

STEERING LINK ASSEMBLY

*3

STEERING INTERMEDIATE SHAFT ASSEMBLY

*4

FRONT NO. 1 STABILIZER BRACKET LH

*5

FRONT NO. 1 STABILIZER BRACKET RH

*6

FRONT NO. 2 STABILIZER BRACKET LH

*7

FRONT NO. 2 STABILIZER BRACKET RH

-

-

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf)

N*m (kgf*cm, ft.*lbf): Specified torque

*1

ENGINE WIRE

*2

FRONT ENGINE MOUNTING INSULATOR

*3

REAR ENGINE MOUNTING INSULATOR

*4

ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

*5

ENGINE MOUNTING SPACER

*6

ENGINE MOUNTING INSULATOR LH

*7

FRONT FRAME ASSEMBLY

*8

FRAME SIDE RAIL PLATE SUB-ASSEMBLY LH

*9

FRAME SIDE RAIL PLATE SUB-ASSEMBLY RH

*10

FRONT SUSPENSION MEMBER BRACKET SUB-ASSEMBLY LH

*11

FRONT SUSPENSION MEMBER BRACKET SUB-ASSEMBLY RH

*12

HOLE PLUG

*13

NO. 2 ENGINE MOUNTING STAY RH

*14

NO. 2 VACUUM SWITCHING VALVE ASSEMBLY

*15

VACUUM HOSE

*16

NO. 1 RELAY BLOCK COVER

*17

ENGINE ASSEMBLY WITH TRANSAXLE

-

-

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf)

N*m (kgf*cm, ft.*lbf): Specified torque

*A

for AWD

*B

Type A

*C

Type B

-

-

*1

DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

*2

NO. 1 CRANKSHAFT POSITION SENSOR PLATE

*3

DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

*4

REAR DRIVE PLATE SPACER

*5

FLYWHEEL HOUSING UNDER COVER

*6

STARTER ASSEMBLY

*7

TRANSFER STIFFENER PLATE RH

*8

FRONT ENGINE MOUNTING BRACKET

*9

AUTOMATIC TRANSAXLE ASSEMBLY

-

-

*a

BLACK COLOR: x 1

SILVER COLOR: x 5

*b

44 mm (1.73 in.)

*c

41 mm (1.61 in.)

-

-

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf)

N*m (kgf*cm, ft.*lbf): Specified torque

Adhesive 1324

★

Precoated part