Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual: Removal

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel pump removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

*1: When performing learning using the Techstream.

Click here

Battery terminal is disconnected/reconnected

Memorize steering angle neutral point

Lane Control System

Pre-collision system

Intelligent clearance sonar system*1

Lighting system (w/ Automatic Headlight Beam Level Control System)

Parking assist monitor system

Panoramic view monitor system

Initialize back door lock

Power door lock control system

Reset back door close position

Power Back Door System (w/ Outside Door Control Switch)

Replacement of fuel pump

Inspection After Repair

  • Poor idle, etc.
  • Engine start function, etc.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here

2. DISCHARGE FUEL SYSTEM PRESSURE

Click here

3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here

4. REMOVE REAR DOOR SCUFF PLATE LH

Click here

5. REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

6. REMOVE REAR SEAT ASSEMBLY LH

Click here

7. REMOVE REAR SEAT ASSEMBLY RH

Click here

8. REMOVE UPPER QUARTER TRIM PAD LH

Click here

9. REMOVE REAR SEAT SIDE GARNISH LH

Click here

10. REMOVE UPPER QUARTER TRIM PAD RH

HINT:

Use the same procedure as for the LH side.

11. REMOVE REAR SEAT SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.

12. REMOVE REAR FLOOR SERVICE HOLE COVER

(a) Remove the 3 clips and turn back the front floor carpet assembly.

(b) Turn back the rear floor silencer.

(c) Using a clip remover with its tip wrapped with protective tape, remove the rear floor service hole cover and butyl tape.

*a

Protective Tape

(d) Disconnect the 2 fuel pump connectors.

13. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

(a) Remove the tube joint clip, and pull off the fuel tube joint of the fuel tank main tube sub-assembly.

*1

Fuel Suction Plate Sub-assembly

*2

Tube Joint Clip

*a

Fuel Tube Joint

*b

O-ring

*c

Nylon Tube

Pull off

Pull off

NOTICE:

  • Remove any foreign matter on the fuel tube joint before performing this work.
  • Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).
  • Be sure to disconnect the fuel tube joint by hand.
  • Do not bend, twist, pinch or kink the nylon tube.
  • Cover the disconnected fuel tube joint with a plastic bag to prevent damage and contamination.
  • If the fuel tube joint and fuel suction plate sub-assembly are stuck, push and pull to release them.

14. REMOVE FUEL PUMP GAUGE RETAINER

NOTICE:

Before performing these procedures, first cover the connectors and fuel tube joint of the fuel suction tube with pump and gauge assembly with vinyl tape and then clean any dirt and foreign matter in order to prevent contamination of the fuel system.

(a) Install SST (fuel pump holding tool assy) to the fuel pump gauge retainer.

(1) Insert SST (claw No. 1) between the service hole and fuel pump gauge retainer as shown in the illustration.

*a

SST (Claw No. 1)

*b

Wide

SST: 09808-14050

09882-14050

(2) Align the detent of the tank suction tube support and cutout of SST (claw No. 1).

*a

SST (Claw No. 1)

*b

Detent of Tank Suction Tube Support

Front

-

-

(3) Insert SST (claw) between the service hole and fuel pump gauge retainer as shown in the illustration.

*a

SST (Claw No. 1)

*b

SST (Claw)

SST: 09808-14040

09882-14040

(4) Insert SST (claw No. 2) between the service hole and fuel pump gauge retainer, and align it with the second detent of the tank suction tube support.

*a

SST (Claw No. 1)

*b

SST (Claw No. 2)

*c

SST (Bridge)

*d

SST (Bolt)

*e

Narrow

*f

Contact

*g

Cloth

*h

Detent of Tank Suction Tube Support

SST: 09808-14050

09881-14050

09882-14050

09883-14050

09884-14050

(5) Install SST (bridge) to SST (claw No. 1) and SST (claw No. 2) with 2 SST (bolt).

(6) Place a piece of cloth or equivalent on the fuel suction tube with pump and gauge assembly and lightly tighten 2 SST (bolt) of SST (bridge) until they come into contact with the fuel suction tube with pump and gauge assembly.

NOTICE:

If a piece of cloth or equivalent is not placed between the fuel suction tube with pump and gauge assembly and 2 SST (bolt), the fuel suction tube with pump and gauge assembly may be damaged.

(b) Install SST (fuel pump retainer tool assy) to the fuel pump gauge retainer.

(1) Position SST (claw) next to SST (claw No. 1) so that the protrusions of the fuel pump gauge retainer are aligned with the grooves of SST (claw). Insert the second SST (claw) between the service hole and fuel pump gauge retainer, and position it next to SST (claw No. 2) so that it is opposite to SST (claw), and the protrusions of the fuel pump gauge retainer are aligned with the grooves of SST (claw).

*a

SST (Claw No. 1)

*b

SST (Claw No. 2)

*c

SST (Claw)

*d

SST (Bridge)

*e

Triangle Mark

*f

Protrusion of Fuel Pump Gauge Retainer

*g

Groove of SST (Claw)

*h

Correct

*i

Incorrect

-

-

SST: 09808-14040

09882-14040

NOTICE:

Ensure that SST (claw) does not cover the triangle mark of the fuel pump gauge retainer.

(2) While ensuring that SST (plate) is centered, install SST (plate) to 2 SST (claw) with 2 SST (bolt and washer set).

SST: 09808-14040

09881-14040

09883-14040

*a

SST (Claw No. 1)

*b

SST (Claw No. 2)

*c

SST (Claw)

*d

SST (Bridge)

*e

SST (Plate)

*f

SST (Bolt and Washer Set)

(c) Attach 2 breaker bars to SST (fuel pump holding tool assy) and 1 breaker bar to SST (fuel pump retainer tool assy).

*a

SST (Fuel Pump Holding Tool Assy)

*b

SST (Fuel Pump Retainer Tool Assy)

(d) Place paint marks on the fuel suction tube with pump and gauge assembly, fuel pump gauge retainer and fuel tank assembly as shown in the illustration.

*a

Paint Mark

(e) While holding the 2 breaker bars attached to SST (fuel pump holding tool assy), turn the breaker bar attached to SST (fuel pump retainer tool assy) to loosen the fuel pump gauge retainer. [*1]

*a

SST (Fuel Pump Holding Tool Assy)

*b

SST (Fuel Pump Retainer Tool Assy)

*c

Holding

*d

Turn

*e

Push down

-

-

NOTICE:

Push down on the 2 locations shown in the illustration to prevent SST (fuel pump holding tool assy) from turning.

(f) Check that only the paint mark on the fuel pump gauge retainer has moved.

*a

Paint Mark

*b

Correct

*c

Incorrect

-

-

HINT:

If the paint mark on the fuel suction tube with pump and gauge assembly has also moved, tighten the fuel pump gauge retainer until the paint marks are aligned at the original position. Then repeat from step [*1].

(g) Loosen the fuel pump gauge retainer by using SST (fuel pump retainer tool assy) until the fuel pump gauge retainer turns approximately 360°.

*a

SST (Claw)

*b

SST (Fuel Pump Holding Tool Assy)

*c

SST (Fuel Pump Retainer Tool Assy)

-

-

(h) Remove SST (fuel pump retainer tool assy) and SST (fuel pump holding tool assy) from the fuel pump gauge retainer.

(i) Check that the fuel pump gauge retainer can be loosened by hand.

HINT:

If the fuel pump gauge retainer cannot be loosened by hand, use SST (fuel pump retainer tool assy) to loosen the fuel pump gauge retainer.

*a

SST (Fuel Pump Retainer Tool Assy)

-

-

SST: 09808-14040

09881-14040

09882-14040

09883-14040

(j) While holding the fuel suction tube with pump and gauge assembly by hand, remove the fuel pump gauge retainer.

15. REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

(a) Remove the fuel suction tube with pump and gauge assembly from the fuel tank assembly.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.

(b) Remove the fuel suction tube set gasket from the fuel tank assembly.

*1

Fuel Suction Tube Set Gasket

    Disassembly
    DISASSEMBLY CAUTION / NOTICE / HINT NOTICE: Do not disconnect the tube shown in the illustration when disassembling the fuel suction tube with pump and gauge assembly. Doing so will cause reassembl ...

    Inspection
    INSPECTION PROCEDURE 1. INSPECT FUEL PUMP (a) Measure the resistance according to the value(s) in the table below. Standard Resistance: Tester Connection Specified Condition U - V 0.05 ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Front Axle Hub: On-vehicle Inspection
    ON-VEHICLE INSPECTION CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH side and LH side. The following procedure is for the LH side. PROCEDURE 1. REMOVE FRONT WHEEL Click here 2. SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY Click here 3. REMOVE FRONT DISC Click here 4. INS ...

    Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Intuitive Parking Assist System (w/ Intelligent Clearance Sonar System): Data List / Active Test
    DATA LIST / ACTIVE TEST DATA LIST NOTICE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not. HINT: Using the Techstream to read the Data List allows the values or states of ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2024 Copyright www.lexusrx.net
    0.0204