CAUTION / NOTICE / HINT
HINT:
Click here
PROCEDURE
1. | VEHICLE BROUGHT TO WORKSHOP |
|
2. | CUSTOMER PROBLEM ANALYSIS |
HINT:
What | Vehicle model, system name |
When | Date, time, occurrence frequency |
Where | Road conditions |
Under what conditions? | Driving conditions, weather conditions |
How did it happen? | Problem symptoms |
|
3. | PRE-CHECK |
(a) Measure the battery voltage.
Standard Voltage:
11 to 14 V
If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.
(b) Check the fuses and relays.
(c) Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.
|
4. | CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM* |
(a) Using the Techstream, check for CAN communication system DTCs.
Click here
Result | Proceed to |
---|---|
CAN DTCs are not output | A |
CAN DTCs are output | B |
B | ![]() | GO TO CAN COMMUNICATION SYSTEM |
|
5. | CHECK FOR DTC* |
(a) Check for DTCs.
Body Electrical > Front Radar Sensor > Trouble Codes Result | Proceed to |
---|---|
DTCs are not output | A |
DTC C1A1100 is output | B |
DTCs other than C1A1100 are output | C |
A | ![]() | GO TO STEP 7 |
B | ![]() | GO TO DTC CHART (C1A1100) |
|
6. | RECONFIRM DTC OUTPUT* |
(a) Using the Techstream, Clear the DTCs.
Body Electrical > Front Radar Sensor > Clear DTCs(b) Reproduce the vehicle conditions that were present when the DTCs that were noted were stored.
HINT:
Refer to each corresponding DTC for details on the detection conditions.
Click here
(c) Using the Techstream, check for DTCs.
Body Electrical > Front Radar Sensor > Trouble Codes Result | Proceed to |
---|---|
DTCs are not output | A |
DTCs are output | B |
B | ![]() | GO TO DTC CHART |
|
7. | CHECK VEHICLE CONTROL HISTORY* |
(a) Using the Techstream, check for Vehicle Control History (RoB).
Body Electrical > Front Radar Sensor > Utility Tester Display |
---|
Vehicle Control History (RoB) |
(b) Make a note of the output Vehicle Control History (RoB).
Result | Proceed to |
---|---|
Vehicle Control History (RoB) codes are not output | A |
Vehicle Control History (RoB) code X2026 or X2028 is output | B |
Vehicle Control History (RoB) codes other than X2026 and X2028 are output | C |
A | ![]() | GO TO SYMPTOM SIMULATION |
B | ![]() | GO TO VEHICLE CONTROL HISTORY (X2026 or X2028) |
|
8. | RECONFIRM VEHICLE CONTROL HISTORY* |
(a) Using the Techstream, clear the Vehicle Control History (RoB).
Body Electrical > Front Radar Sensor > Utility Tester Display |
---|
Vehicle Control History (RoB) |
(b) Using the Techstream, check for Vehicle Control History (RoB).
Body Electrical > Front Radar Sensor > Utility Tester Display |
---|
Vehicle Control History (RoB) |
Result | Proceed to |
---|---|
Vehicle Control History (RoB) codes are not output | A |
Vehicle Control History (RoB) codes are output | B |
A | ![]() | GO TO SYMPTOM SIMULATION |
B | ![]() | GO TO VEHICLE CONTROL HISTORY |
Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Fuel Pressure Sensor (for High Pressure): Inspection
INSPECTION PROCEDURE 1. INSPECT FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY LH (FUEL PRESSURE SENSOR) NOTICE:
Do not remove the fuel pressure sensor from the fuel delivery pipe with sensor assembly LH.
If the fuel pressure sensor is removed, replace the fuel delivery pipe with sensor assembly LH (f ...
Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Rear Axle Carrier (for 2wd): Installation
INSTALLATION CAUTION / NOTICE / HINT HINT:
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
PROCEDURE 1. INSTALL LOWER CONTROL ARM PIN (for TMMC Made) (a) Secure the rear axle carrier sub-assembly in a vise using aluminum plates. NOTICE: Do n ...