Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual: Installation

INSTALLATION

PROCEDURE

1. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

2. INSTALL STEERING COLUMN ASSEMBLY

NOTICE:

Make sure that the wire harness is not interfering with the steering column assembly.

(a) Install the steering column assembly with the bolt and 2 nuts.

Torque:

36 N·m {367 kgf·cm, 27 ft·lbf}

(b) Connect each connector and engage each wire harness clamp to the steering column assembly.

(c) Connect the 2 connectors.

(d) Engage the clamp.

3. INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY

(a) Align the matchmarks on the steering intermediate shaft assembly and steering column assembly.

*a

Matchmark

(b) Install the steering intermediate shaft assembly to the steering column assembly.

(c) Install a new bolt.

Torque:

64 N·m {653 kgf·cm, 47 ft·lbf}

(d) Tighten the bolt.

4. CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

Click here

5. INSTALL STOP LIGHT SWITCH ASSEMBLY

Click here

6. INSTALL NO. 4 AIR DUCT SUB-ASSEMBLY

(a) Engage the 3 claws to install a new No. 4 air duct sub-assembly.

(b) Install the bolt.

Torque:

9.8 N·m {100 kgf·cm, 87 in·lbf}

7. INSTALL FRONT NO. 1 CONSOLE BOX INSERT

Click here

8. INSTALL CONSOLE BOX ASSEMBLY

Click here

9. INSTALL CONSOLE REAR END PANEL SUB-ASSEMBLY

Click here

10. INSTALL CONSOLE PANEL SUB-ASSEMBLY

Click here

11. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY

Click here

12. INSTALL REAR CONSOLE UPPER PANEL

Click here

13. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Click here

14. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

NOTICE:

  • Do not replace the spiral cable with sensor sub-assembly with the battery connected and the engine switch on (IG).
  • Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the battery connected and the engine switch on (IG).
  • Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.

Install in this direction

(a) Engage the 3 claws to install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly.

(b) Connect each connector to the turn signal switch assembly with spiral cable sub-assembly.

15. INSTALL UPPER STEERING COLUMN COVER

(a) Engage the 6 clips to the upper steering column cover.

(b) Engage the 2 claws to install the upper steering column cover.

Install in this direction

16. INSTALL LOWER STEERING COLUMN COVER

(a) Engage the 2 claws to install the lower steering column cover.

(b) Install the 3 screws.

Torque:

2.0 N·m {20 kgf·cm, 18 in·lbf}

17. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

18. INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

Click here

19. INSTALL STEERING WHEEL ASSEMBLY

Click here

20. CHECK STEERING WHEEL CENTER POINT

21. INSTALL HORN BUTTON ASSEMBLY

Click here

22. CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM

(a) Set the auto tilt away function setting to the previous condition by changing the customize parameter.

Click here

23. PERFORM CALIBRATION OF TORQUE SENSOR ZERO POINT

Click here

24. ADJUST PARKING ASSIST MONITOR SYSTEM

Click here

25. ADJUST PANORAMIC VIEW MONITOR SYSTEM (w/ Panoramic View Monitor System)

Click here

26. ADJUST INTELLIGENT CLEARANCE SONAR SYSTEM (w/ Intelligent Clearance Sonar System)

Click here

    Inspection
    INSPECTION PROCEDURE 1. INSPECT PRELOAD (a) Secure the steering column assembly in a vise using aluminum plates, cloths and wooden blocks. NOTICE: Do not overtighten the vise, as the steering ...

    Reassembly
    REASSEMBLY CAUTION / NOTICE / HINT NOTICE: Do not drop the power steering ECU assembly, strike it with tools or subject it to impacts. If the power steering ECU assembly is subjected to an impact ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Towing Converter System: Precaution
    PRECAUTION PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE BATTERY TERMINAL NOTICE: When disconnecting the cable from the negative (-) battery terminal, initialize the following systems after the cable is reconnected: System See Procedure Lane Control System Pre-collision System ...

    Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Can Communication System: Check Bus 1 Line for Short to +B
    DESCRIPTION There may be a short circuit between one of the CAN bus lines and +B when there is no resistance between terminal 23 (CA1H) of the network gateway ECU and terminal 16 (BAT) of the DLC3, or terminal 8 (CA1L) of the network gateway ECU and terminal 16 (BAT) of the DLC3. Symptom Troubl ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2025 Copyright www.lexusrx.net
    0.0145