PRECAUTION
PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable from the negative (-) battery terminal, initialize the following system(s) after the cable is reconnected.
System | Procedure |
---|---|
Lane Control System | |
Pre-collision System | |
Intelligent Clearance Sonar System | |
Parking Assist Monitor System | |
Panoramic View Monitor System | |
Lighting System (w/ Automatic Headlight Beam Level Control System) | |
Power Door Lock Control System | |
Power Back Door System (w/ Outside Door Control Switch) |
HANDLING PRECAUTIONS FOR SRS AIRBAG SYSTEM
(a) This vehicle is equipped with a Supplemental Restraint System (SRS). Failure to carry out service operations in the correct sequence could cause the SRS to unexpectedly deploy during servicing. This may cause a serious accident.
Before servicing (including inspection, replacement, removal and installation of parts), be sure to read the precautionary notices for the Supplemental Restraint System.
Click here
PRECAUTIONS FOR REMOVAL, INSTALLATION AND REPLACEMENT OF ELECTRONIC POWER STEERING COMPONENTS
(a) Be sure to align the front wheels straight ahead when removing and installing the steering gear assembly.
(b) When disconnecting the steering intermediate shaft assembly, be sure to place matchmarks before starting the operation.
(c) After replacing the electric power steering column sub-assembly or power steering ECU assembly, calibrate the torque sensor zero point.
Click here
HANDLING PRECAUTION
(a) When handling electronic parts:
(1) Do not subject any parts such as ECUs and relays to any impact. Replace them with new ones if dropped or subjected to a strong impact.
(2) Do not expose any electronic parts to high temperatures or humidity.
(3) In order to prevent deformation or malfunctions due to static electricity, do not touch the connector terminals.
(b) When handling the power steering ECU assembly:
(1) When the power steering ECU assembly has been replaced, perform assist map writing and torque sensor zero point calibration.
Click here
(c) When handling the electric power steering column sub-assembly:
(1) Do not subject the electric power steering column sub-assembly (especially the motor and torque sensor) to any impact. Replace the electric power steering column sub-assembly with a new one if subjected to a strong impact.
(2) Do not pull the wire harness when moving the electric power steering column sub-assembly.
(3) If the electric power steering column sub-assembly has been replaced, perform torque sensor zero point calibration.
Click here
(d) When disconnecting and reconnecting the connectors:
(1) Before disconnecting connectors related to the power steering system, turn the engine switch on (IG), center the steering wheel, turn the engine switch off, and then disconnect the connectors.
(2) Before reconnecting connectors related to the power steering system, ensure that the engine switch is off. Then center the steering wheel and turn the engine switch on (IG).
NOTICE:
Do not turn the engine switch on (IG) when the steering wheel is not centered.
(3) If the above operations are not carried out properly, the steering center point (zero point) will deviate, which may lead to a difference in steering effort between turning right and left. If there is a difference in steering effort between turning right and left, perform torque sensor zero point calibration after initializing the torque sensor zero point.
Click here
PRECAUTIONS FOR CAN COMMUNICATION
(a) CAN communication lines are used to receive information from the skid control ECU (brake actuator assembly) and ECM and to transmit warnings to the combination meter assembly. When problems are detected in the CAN communication lines, CAN communication DTCs are stored.
(b) If any CAN communication system DTCs are output, perform troubleshooting for the CAN communication system first.
(c) The wiring used for each communication line is a twisted pair of wires that have an equal length. Do not temporarily repair a CAN communication line with a bypass wire or equivalent.
Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Automatic Transaxle System: Terminals Of Ecm
TERMINALS OF ECM ECM HINT: The standard voltage and resistance of each ECM terminal is shown in the table below. In the table, first follow the information under "Condition". Look under "Terminal No. (Symbol)" for the terminals to be inspected. The standard voltage or resistance between the termina ...
Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Electric Parking Brake Actuator: On-vehicle Inspection
ON-VEHICLE INSPECTION PROCEDURE 1. INSPECT PARKING BRAKE ACTUATOR ASSEMBLY HINT: Using the Techstream to perform the Active Tests allows relays, VSVs and actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermitt ...