REASSEMBLY
PROCEDURE
1. INSTALL POWER BACK DOOR UNIT SET ASSEMBLY LH
NOTICE:
Do not apply any horizontal load to the power back door unit set assembly in order to prevent the piston rod from deforming.
(a) Clean the bolt hole on the vehicle body.
(b) Install the 2 bolts (A). NOTICE: Install the power back door unit set assembly while supporting the back door by hand. Torque: 8.0 N·m {82 kgf·cm, 71 in·lbf} |
|
(c) Install the power back door unit set assembly with 2 new bolts (B).
NOTICE:
Install the power back door unit set assembly while supporting the back door by hand.
Torque:
8.0 N·m {82 kgf·cm, 71 in·lbf}
2. INSTALL POWER BACK DOOR UNIT SET ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
3. INSTALL BACK DOOR DUST PROOF SEAL
(a) Engage the guide and 2 claws to install the back door dust proof seal. HINT: Use the same procedure for the RH side and LH side. |
|
4. INSTALL BACK DOOR LOWER STOPPER CUSHION
(a) Engage the 2 claws to install a new back door lower stopper cushion. HINT: Use the same procedure for the RH side and LH side. |
|
5. INSTALL REAR TELEVISION CAMERA ASSEMBLY
Click here
6. INSTALL REAR LIGHT ASSEMBLY LH (for Bulb Type Turn Signal Light)
Click here
7. INSTALL REAR LIGHT ASSEMBLY RH (for Bulb Type Turn Signal Light)
HINT:
Use the same procedure as for the LH side.
8. INSTALL REAR LIGHT ASSEMBLY LH (for LED Type Turn Signal Light)
Click here
9. INSTALL REAR LIGHT ASSEMBLY RH (for LED Type Turn Signal Light)
HINT:
Use the same procedure as for the LH side.
10. INSTALL POWER BACK DOOR WARNING BUZZER
Click here
11. INSTALL MULTIPLEX NETWORK DOOR ECU
Click here
12. INSTALL LICENSE PLATE LIGHT ASSEMBLY LH
Click here
13. INSTALL LICENSE PLATE LIGHT ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
14. INSTALL BACK DOOR OPENER SWITCH ASSEMBLY
Click here
15. INSTALL BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY
Click here
16. INSTALL REAR WIPER MOTOR AND BRACKET ASSEMBLY
Click here
17. INSTALL SIDE REAR SPOILER PROTECTOR SUB-ASSEMBLY LH
Click here
18. INSTALL SIDE REAR SPOILER PROTECTOR SUB-ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
19. INSTALL POWER BACK DOOR SENSOR ASSEMBLY LH (w/o Rear No. 2 Seat)
Click here
20. INSTALL POWER BACK DOOR SENSOR ASSEMBLY LH (w/ Rear No. 2 Seat)
Click here
21. INSTALL POWER BACK DOOR SENSOR ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
22. INSTALL BACK DOOR LOWER STOPPER
(a) Engage the guide to install the back door lower stopper with the bolt. HINT: Use the same procedure for the RH side and LH side. |
|
23. INSTALL BACK DOOR STAY REINFORCEMENT LH (w/ Rear No. 2 Seat)
(a) Engage the guide to install the back door stay reinforcement LH with the bolt. |
|
24. INSTALL BACK DOOR STAY REINFORCEMENT RH (w/ Rear No. 2 Seat)
HINT:
Use the same procedure as for the LH side.
25. INSTALL BACK DOOR LOWER STAY REINFORCEMENT LH
(a) Engage the 2 guides to install the back door lower stay reinforcement LH with the 2 bolts. Torque: 5.5 N·m {56 kgf·cm, 49 in·lbf} |
|
26. INSTALL BACK DOOR LOWER STAY REINFORCEMENT RH
HINT:
Use the same procedure as for the LH side.
27. INSTALL BACK DOOR LOCK ASSEMBLY
Click here
28. INSTALL BACK DOOR TRIM PANEL ASSEMBLY (w/o Rear No. 2 Seat)
(a) Engage the 16 clips to install the back door trim panel assembly as shown in the illustration.
![]() | Install in this Direction |
29. INSTALL BACK DOOR TRIM PANEL ASSEMBLY (w/ Rear No. 2 Seat)
(a) Engage the 17 clips to install the back door trim panel assembly as shown in the illustration.
![]() | Install in this Direction |
30. INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY
Click here
31. INSTALL DOOR PULL HANDLE
(a) Connect each connector.
(b) Engage the 6 claws to install the door pull handle. |
|
32. INSTALL BACK DOOR TRIM BASE
(a) Engage the 4 claws to install the back door trim base. |
|
33. INSTALL BACK DOOR LOCK COVER (w/o Rear No. 2 Seat)
(a) Engage the 4 claws to install the back door lock cover. |
|
34. INSTALL BACK DOOR LOCK COVER (w/ Rear No. 2 Seat)
(a) Engage the 4 claws to install the back door lock cover. |
|
35. INSTALL BACK DOOR TRIM COVER LH (w/o Rear No. 2 Seat)
(a) Engage the 2 guides, 2 claws and 2 clips to install the back door trim cover LH as shown in the illustration.
![]() | Install in this Direction |
36. INSTALL BACK DOOR TRIM COVER LH (w/ Rear No. 2 Seat)
(a) Engage the 2 guides, 2 claws and 2 clips to install the back door trim cover LH as shown in the illustration.
![]() | Install in this Direction |
37. INSTALL BACK DOOR TRIM COVER RH
HINT:
Use the same procedure as for the LH side.
38. INSTALL BACK WINDOW UPPER PANEL TRIM (w/o Rear No. 2 Seat)
(a) Disengage the 4 guides, 5 clips and 4 claws to install the back window upper panel trim. |
|
39. INSTALL BACK WINDOW UPPER PANEL TRIM (w/ Rear No. 2 Seat)
(a) Disengage the 4 guides, 6 clips and 4 claws to install the back window upper panel trim. |
|
40. INITIALIZE POWER BACK DOOR SYSTEM
Click here
41. INSPECT POWER BACK DOOR SYSTEM
Click here
42. INSPECT BACK DOOR CLOSER SYSTEM
Click here
43. ADJUST REAR TELEVISION CAMERA ASSEMBLY
w/ Parking Assist Monitor System: Click here
w/ Panoramic View Monitor System: Click here
Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Audio And Visual System (for 12.3 Inch Display): Stereo Jack Adapter Light does not Illuminate
DESCRIPTION Power is supplied to the No. 1 stereo jack adapter assembly illumination from the radio receiver assembly. WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE: Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibra ...
Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Power Mirror Control System (w/o Memory): Customize Parameters
CUSTOMIZE PARAMETERS CUSTOMIZE POWER MIRROR CONTROL SYSTEM (w/o Memory) HINT: The following items can be customized. NOTICE:
When the customer requests a change in a function, first make sure that the function can be customized.
Record the current settings before customizing.
(a) Customizing ...