DESCRIPTION
The sliding roof ECU (sliding roof drive gear assembly) and roof sunshade ECU (sliding roof drive gear assembly) receive each other's position information from the main body ECU (multiplex network body ECU) via LIN communication.
The sliding roof ECU (sliding roof drive gear assembly) and roof sunshade ECU (sliding roof drive gear assembly) receive signals from each switch, and operate their built-in motors.
For the linked functions of the sliding roof and roof sunshade refer to Operation Check.
Click here
WIRING DIAGRAM
Refer to SYSTEM DIAGRAM.
Click here
CAUTION / NOTICE / HINT
NOTICE:
Click here
Click here
Click here
Click here
PROCEDURE
1. | CHECK FOR DTC (MAIN BODY) |
(a) Clear the DTCs.
Click here
(b) Check for DTCs.
Click here
OK:
DTCs B1273 and B2329 are not output.
NG | ![]() | GO TO LIN COMMUNICATION SYSTEM (Proceed to How to Proceed with Troubleshooting) |
|
2. | CHECK FOR DTC (SLIDING ROOF AND SLIDING SUNSHADE) |
(a) Clear the DTCs.
Click here
(b) Check for DTCs.
Click here
OK:
DTCs B2341 and B2344 are not output.
NG | ![]() | GO TO DIAGNOSTIC TROUBLE CODE CHART |
|
3. | CHECK POWER WINDOW CONTROL SYSTEM |
(a) Check the power window control system operates normally.
Click here
OK:
The power window control system operates normally.
NG | ![]() | GO TO POWER WINDOW CONTROL SYSTEM |
|
4. | READ VALUE USING TECHSTREAM (SLIDING ROOF) |
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Sliding Roof / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Sliding Roof > Data List Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
---|---|---|---|---|
Vent Switch | Sliding roof tilt switch signal | OFF or ON | OFF: Sliding roof switch not pressed ON: Sliding roof switch pressed | - |
Roof Open Switch | Sliding roof open switch signal | OFF or ON | OFF: Sliding roof switch not slid backward ON: Sliding roof switch slid backward | - |
Roof Close Switch | Sliding roof close switch signal | OFF or ON | OFF: Sliding roof switch not slid forward ON: Sliding roof switch slid forward | - |
Shade Close Switch | Roof sunshade close switch signal | OFF or ON | OFF: Roof sunshade switch not slid forward ON: Roof sunshade switch slid forward | - |
Shade Open Switch | Roof sunshade open switch signal | OFF or ON | OFF: Roof sunshade switch not slid backward ON: Roof sunshade switch slid backward | - |
Tester Display |
---|
Vent Switch |
Roof Open Switch |
Roof Close Switch |
Shade Close Switch |
Shade Open Switch |
OK:
The Techstream display changes according to switch operation as shown in the table.
NG | ![]() | GO TO STEP 8 |
|
5. | READ VALUE USING TECHSTREAM (SLIDING SUNSHADE) |
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Sliding Sunshade / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Sliding Sunshade > Data List Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
---|---|---|---|---|
Vent Switch | Sliding roof tilt switch signal | OFF or ON | OFF: Sliding roof switch not pressed ON: Sliding roof switch pressed | - |
Roof Open Switch | Sliding roof open switch signal | OFF or ON | OFF: Sliding roof switch not slid backward ON: Sliding roof switch slid backward | - |
Roof Close Switch | Sliding roof close switch signal | OFF or ON | OFF: Sliding roof switch not slid forward ON: Sliding roof switch slid forward | - |
Shade Close Switch | Roof sunshade close switch signal | OFF or ON | OFF: Roof sunshade switch not slid forward ON: Roof sunshade switch slid forward | - |
Shade Open Switch | Roof sunshade open switch signal | OFF or ON | OFF: Roof sunshade switch not slid backward ON: Roof sunshade switch slid backward | - |
Tester Display |
---|
Vent Switch |
Roof Open Switch |
Roof Close Switch |
Shade Close Switch |
Shade Open Switch |
OK:
The Techstream display changes according to switch operation as shown in the table.
OK | ![]() | USE SIMULATION METHOD TO CHECK |
|
6. | INSPECT MAP LIGHT ASSEMBLY |
(a) Remove the map light assembly.
Click here
(b) Inspect the map light assembly.
Click here
NG | ![]() | REPLACE MAP LIGHT ASSEMBLY |
|
7. | CHECK HARNESS AND CONNECTOR (ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) - MAP LIGHT ASSEMBLY AND BODY GROUND) |
(a) Disconnect the w1 roof sunshade ECU (sliding roof drive gear assembly) connector.
(b) Disconnect the U2 sliding roof ECU (Sliding roof drive gear assembly) connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
---|---|---|
w1-10 (OPN) - U11-11 (OPN) | Always | Below 1 Ω |
w1-10 (OPN) or U11-11 (OPN) - Body ground | Always | 10 kΩ or higher |
w1-8 (CLS) - U11-12 (CLS) | Always | Below 1 Ω |
w1-8 (CLS) or U11-12 (CLS) - Body ground | Always | 10 kΩ or higher |
w1-4 (VENT) - U11-7 (B) | Always | Below 1 Ω |
w1-4 (VENT) or U11-7 (B) - Body ground | Always | 10 kΩ or higher |
w1-5 (OPN) - U11-23 (UP) | Always | Below 1 Ω |
w1-5 (OPN) or U11-23 (UP) - Body ground | Always | 10 kΩ or higher |
w1-9 (CLS) - U11-24 (DOWN) | Always | Below 1 Ω |
w1-9 (CLS) or U11-24 (DOWN) - Body ground | Always | 10 kΩ or higher |
w1-2 (E) - Body ground | Always | Below 1 Ω |
U11-19 (GND) - Body ground | Always | Below 1 Ω |
OK | ![]() | REPLACE ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) |
NG | ![]() | REPAIR OR REPLACE HARNESS OR CONNECTOR |
8. | INSPECT MAP LIGHT ASSEMBLY |
(a) Remove the map light assembly.
Click here
(b) Inspect the map light assembly.
Click here
NG | ![]() | REPLACE MAP LIGHT ASSEMBLY |
|
9. | CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) - MAP LIGHT ASSEMBLY AND BODY GROUND) |
(a) Disconnect the w1 roof sunshade ECU (sliding roof drive gear assembly) connector.
(b) Disconnect the U2 sliding roof ECU (sliding roof drive gear assembly) connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
---|---|---|
U2-10 (OPN) - U11-11 (OPN) | Always | Below 1 Ω |
U2-10 (OPN) or U11-11 (OPN) - Body ground | Always | 10 kΩ or higher |
U2-8 (CLS) - U11-12 (CLS) | Always | Below 1 Ω |
U2-8 (CLS) or U11-12 (CLS) - Body ground | Always | 10 kΩ or higher |
U2-4 (TILT) - U11-7 (B) | Always | Below 1 Ω |
U2-4 (TILT) or U11-7 (B) - Body ground | Always | 10 kΩ or higher |
U2-5 (OPN) - U11-23 (UP) | Always | Below 1 Ω |
U2-5 (OPN) or U11-23 (UP) - Body ground | Always | 10 kΩ or higher |
U2-9 (CLS) - U11-24 (DOWN) | Always | Below 1 Ω |
U2-9 (CLS) or U11-24 (DOWN) - Body ground | Always | 10 kΩ or higher |
U2-2 (E) - Body ground | Always | Below 1 Ω |
U11-19 (GND) - Body ground | Always | Below 1 Ω |
OK | ![]() | REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) |
NG | ![]() | REPAIR OR REPLACE HARNESS OR CONNECTOR |
Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Power Steering System: EPS Warning Light Circuit
DESCRIPTION If the power steering ECU assembly detects a malfunction, the power steering ECU assembly stores a DTC and illuminates the EPS warning light. WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE:
If the power steering ECU assembly has been replaced, perform assist map writing and torque sen ...
Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Navigation System: Problem Symptoms Table
PROBLEM SYMPTOMS TABLE NOTICE: Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System. Click here HINT:
Use the table below to help determine the cause of ...