Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual: Position Initialization Incomplete (B2343)

Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual / Vehicle Exterior / Sliding Roof / Convertible / Sliding Roof System / Position Initialization Incomplete (B2343)

DESCRIPTION

This DTC is stored when the sliding roof ECU (sliding roof drive gear sub-assembly) has not been initialized.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

B2343

Position Initialization Incomplete

Sliding roof ECU (sliding roof drive gear sub-assembly) has not been initialized

Sliding roof ECU (Sliding roof drive gear sub-assembly)

WIRING DIAGRAM

Refer to DTC B2341.

Click here

CAUTION / NOTICE / HINT

NOTICE:

  • If the sliding roof ECU (sliding roof drive gear sub-assembly) is removed and reinstalled or replaced, the sliding roof ECU (sliding roof drive gear sub-assembly) must be initialized.

    Click here

  • The sliding roof system uses the LIN communication system. First, confirm that there are no malfunctions in the LIN communication system. Refer to How to Proceed with Troubleshooting.

    Click here

HINT:

When DTC B2342 and B2343 are output simultaneously, perform troubleshooting for DTC B2342 first.

PROCEDURE

1.

INITIALIZE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

(a) Check that the sliding roof ECU (sliding roof drive gear sub-assembly) can be initialized.

Click here

OK:

Sliding roof ECU (sliding roof drive gear sub-assembly) can be initialized.

NG

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

OK

2.

CHECK SLIDING ROOF OPERATION

(a) Check the sliding roof auto operation.

Click here

OK:

Auto operation operates normally.

NG

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

OK

3.

CHECK DTC OUTPUT

(a) Clear the DTCs.

Click here

Body Electrical > Sliding Roof > Clear DTCs

(b) Check for DTCs.

Body Electrical > Sliding Roof > Trouble Codes

OK:

DTC B2343 is not output.

OK

END (MALFUNCTION DUE TO INITIALIZATION FAILURE)
NG

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

    Switch Failure (B2342)
    DESCRIPTION This DTC is stored when the sliding roof ECU (sliding roof drive gear sub-assembly) detects that the sliding roof switch (map light assembly) is stuck for 30 seconds or more. DTC No. ...

    Key-off Operation Function Operates even if Operating Conditions are not Satisfied
    DESCRIPTION The sliding roof ECU (sliding roof drive gear sub-assembly) operates its built-in motor according to the sliding roof switch (map light assembly) operation. Using the sliding roof switch ( ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Amplifier Antenna (w/ Rear No. 2 Seat): Removal
    REMOVAL PROCEDURE 1. REMOVE BACK WINDOW UPPER PANEL TRIM Click here 2. REMOVE BACK DOOR TRIM COVER LH Click here 3. REMOVE BACK DOOR TRIM COVER RH HINT: Use the same procedure as for the LH side. 4. REMOVE BACK DOOR LOCK COVER Click here 5. REMOVE BACK DOOR TRIM BASE Click here 6. REMOVE ...

    Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Rear Seat Assembly (for 60/40 Split Seat Type Rh Side): Inspection
    INSPECTION PROCEDURE 1. PRECAUTION NOTICE: After performing the following check, initialize the fold seat control ECU (initial position reset and initial position memorization). Click here 2. INSPECT REAR SEATBACK FRAME SUB-ASSEMBLY RH (a) Check the operation of the reclining motor. (1) Apply batt ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2025 Copyright www.lexusrx.net
    0.0145