COMPONENTS
ILLUSTRATION
*1 | DECK BOARD ASSEMBLY | *2 | NO. 1 DECK BOARD |
*3 | REAR NO. 4 FLOOR BOARD | *4 | TONNEAU COVER ASSEMBLY |
ILLUSTRATION
*A | w/o Woofer | *B | w/ Woofer |
*1 | DECK SIDE TRIM BOX LH | *2 | FRONT DECK FLOOR BOX |
*3 | REAR DECK FLOOR BOX | *4 | REAR FLOOR FINISH PLATE |
*5 | REAR NO. 2 SEAT ASSEMBLY | - | - |
ILLUSTRATION
*1 | CENTER PILLAR GARNISH ASSEMBLY LH | *2 | FRONT DOOR SCUFF PLATE LH |
*3 | FRONT PILLAR GARNISH LH | *4 | FRONT SEAT OUTER BELT ASSEMBLY LH |
*5 | LOWER CENTER PILLAR GARNISH LH | *6 | REAR DOOR INSIDE SCUFF PLATE LH |
*7 | REAR DOOR SCUFF PLATE LH | *8 | CLIP |
*9 | FRONT PILLAR GARNISH CLIP | - | - |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
ILLUSTRATION
*1 | CENTER PILLAR GARNISH ASSEMBLY RH | *2 | FRONT DOOR SCUFF PLATE RH |
*3 | FRONT PILLAR GARNISH RH | *4 | FRONT SEAT OUTER BELT ASSEMBLY RH |
*5 | LOWER CENTER PILLAR GARNISH RH | *6 | REAR DOOR INSIDE SCUFF PLATE RH |
*7 | REAR DOOR SCUFF PLATE RH | *8 | CLIP |
*9 | FRONT PILLAR GARNISH CLIP | - | - |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
ILLUSTRATION
*1 | COOLER (NO. 2 ROOM TEMP. SENSOR) THERMISTOR | *2 | DECK TRIM SIDE PANEL ASSEMBLY LH |
*3 | FRONT DECK SIDE TRIM COVER LH | *4 | NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY |
*5 | NO. 1 LUGGAGE COMPARTMENT TRIM HOOK | *6 | NO. 2 AIR CONDITIONING CONTROL ASSEMBLY |
*7 | REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH | *8 | REAR ROOF SIDE RAIL GARNISH ASSEMBLY LH |
*9 | REAR SEAT SIDE GARNISH LH | *10 | ROOF SIDE INNER GARNISH ASSEMBLY LH |
*11 | ROPE HOOK ASSEMBLY | *12 | CLIP |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
ILLUSTRATION
*1 | DECK TRIM SIDE PANEL ASSEMBLY RH | *2 | FRONT DECK SIDE TRIM COVER RH |
*3 | NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY | *4 | NO. 1 LUGGAGE COMPARTMENT TRIM HOOK |
*5 | REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH | *6 | REAR ROOF SIDE RAIL GARNISH ASSEMBLY RH |
*7 | REAR SEAT SIDE GARNISH RH | *8 | ROOF SIDE INNER GARNISH ASSEMBLY RH |
*9 | ROPE HOOK ASSEMBLY | *10 | CLIP |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
ILLUSTRATION
*1 | MAP LIGHT ASSEMBLY | *2 | NO. 1 FORWARD RECOGNITION COVER |
*3 | NO. 2 FORWARD RECOGNITION COVER | *4 | RAIN SENSOR |
*5 | RAIN SENSOR COVER | *6 | SPOT LIGHT ASSEMBLY |
ILLUSTRATION
*1 | ASSIST GRIP SUB-ASSEMBLY | *2 | REAR ASSIST GRIP ASSEMBLY LH |
*3 | REAR ASSIST GRIP ASSEMBLY RH | *4 | VISOR ASSEMBLY LH |
*5 | VISOR ASSEMBLY RH | *6 | VISOR BRACKET COVER LH |
*7 | VISOR BRACKET COVER RH | *8 | VISOR HOLDER LH |
*9 | VISOR HOLDER RH | *10 | ASSIST GRIP COVER LH |
*11 | ASSIST GRIP COVER RH | - | - |
● | Non-reusable part | - | - |
ILLUSTRATION
*A | for Standard Roof | *B | for Sliding Roof |
*1 | ROOF HEADLINING ASSEMBLY | - | - |
ILLUSTRATION
*1 | NO. 2 ANTENNA CORD SUB-ASSEMBLY | *2 | WASHER HOSE ASSEMBLY |
ILLUSTRATION
*A | for Standard Roof | - | - |
*1 | NO. 1 ROOF WIRE | *2 | TELEPHONE MICROPHONE ASSEMBLY |
*3 | VANITY LIGHT ASSEMBLY | *4 | NO. 1 MICROPHONE CASE |
*5 | ROOF HEADLINING ASSEMBLY | - | - |
ILLUSTRATION
*A | for Sliding Roof | - | - |
*1 | NO. 1 ROOF WIRE | *2 | TELEPHONE MICROPHONE ASSEMBLY |
*3 | VANITY LIGHT ASSEMBLY | *4 | NO. 1 MICROPHONE CASE |
*5 | ROOF HEADLINING ASSEMBLY | - | - |
Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Maintenance: Under Hood
General MaintenanceGENERAL MAINTENANCE PROCEDURE 1. GENERAL NOTES
Maintenance requirements vary depending on country.
Check the maintenance schedule in the owner's manual.
Following the maintenance schedule is mandatory.
Determine the appropriate time to service the vehicle using either mil ...
Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Engine Assembly: Removal
REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine unit removal/installation are shown below. Necessary Procedure After Parts Removed/Installed/Rep ...