Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual: USB Audio System Recognition/Play Error

Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual / Audio & Visual & Telematics / Audio / Video / Audio And Visual System (for 8 Inch Display) / USB Audio System Recognition/Play Error

DESCRIPTION

When a USB device or "iPod" is connected to the USB jack of the No. 1 stereo jack adapter assembly, it must have playable files. The device must also communicate with and be recognized by the radio receiver assembly. This diagnostic procedure is for when a device is not recognized, or files from the device cannot be played normally.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click here

HINT:

  • When a large amount of data is in a USB device, it may take a while to begin playback.
  • When using a USB device, files that are protected by copyright cannot be played.
  • When files are not played in the sorted order, perform the following procedure before inspection.
    1. Add numbers in front of the file names.
    2. Put the files in a folder and copy the folder data to the USB device.

PROCEDURE

1.

CHECK USB DEVICE OR "iPod"

(a) Disconnect the USB device or "iPod" from the No. 1 stereo jack adapter assembly.

(b) Check if playable files are present on the USB device or "iPod".

HINT:

Refer to System Description for playable files.

Click here

(c) Check if the USB device is a compatible format or "iPod" is a compatible version.

HINT:

Refer to System Description for compatible formats and versions.

Click here

Result

Proceed to

No playable files exist, or incompatible device format or version.

A

Playable files exist, and compatible device format or version.

B
A

END (USB DEVICE FORMAT IS INCOMPATIBLE, "iPod" VERSION IS INCOMPATIBLE, OR NO PLAYABLE FILES EXIST)
B

2.

CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)

(a) Disconnect the J148 radio receiver assembly connector.

(b) Disconnect the J152 No. 1 stereo jack adapter assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

J148-2 (GND2) - J152-3 (GND)

Always

Below 1 Ω

J148-3 (+B) - J152-4 (+B)

Always

Below 1 Ω

J148-16 (ACC) - J152-8 (ACC)

Always

Below 1 Ω

J148-2 (GND2) or J152-3 (GND) - Body ground

Always

10 kΩ or higher

J148-3 (+B) or J152-4 (+B) - Body ground

Always

10 kΩ or higher

J148-16 (ACC) or J152-8 (ACC) - Body ground

Always

10 kΩ or higher
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

3.

CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)

(a) Disconnect the J169 radio receiver assembly connector.

*a

Front view of wire harness connector

(to Radio Receiver Assembly)

*b

Front view of wire harness connector

(to No. 1 Stereo Jack Adapter Assembly)

(b) Disconnect the J170 No. 1 stereo jack adapter assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

J169-1 (USV1) - J170-1 (UPI)

Always

Below 1 Ω

J169-2 (US1-) - J170-2 (UDO-)

Always

Below 1 Ω

J169-3 (US1+) - J170-3 (UDO+)

Always

Below 1 Ω

J169-4 (UGD1) - J170-4 (UJSG)

Always

Below 1 Ω

J169-5 (USG1) - J170-5 (UJSS)

Always

Below 1 Ω

J169-1 (USV1) or J170-1 (UPI) - Body ground

Always

10 kΩ or higher

J169-2 (US1-) or J170-2 (UDO-) - Body ground

Always

10 kΩ or higher

J169-3 (US1+) or J170-3 (UDO+) - Body ground

Always

10 kΩ or higher

J169-4 (UGD1) or J170-4 (UJSG) - Body ground

Always

10 kΩ or higher

J169-5 (USG1) or J170-5 (UJSS) - Body ground

Always

10 kΩ or higher
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

4.

CHECK RADIO RECEIVER ASSEMBLY (NO. 1 STEREO JACK ADAPTER ASSEMBLY POWER SOURCE)

(a) Disconnect the J170 and J152 No. 1 stereo jack adapter assembly connectors.

*a

Front view of wire harness connector

(to No. 1 Stereo Jack Adapter Assembly)

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

J170-1 (UPI) - J170-4 (UJSG)

Engine switch on (ACC)

4.5 to 5.5 V

J152-8 (ACC) - J152-3 (GND)

Engine switch on (ACC)

11 to 14 V

J152-4 (+B) - J152-3 (GND)

Engine switch off

11 to 14 V
NG

REPLACE RADIO RECEIVER ASSEMBLY

OK

5.

FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK

(a) Delete all files in the USB device or "iPod" and format/restore it.

(b) Save the data again and check if it can be played on the in-vehicle device.

NOTICE:

Formatting a USB device or restoring an "iPod" erases all music on the device. Ensure that backup music data is available before performing this operation.

OK:

Malfunction disappears.

OK

END
NG

6.

REPLACE USB DEVICE OR "iPod"

(a) Turn the engine switch off.

HINT:

When this malfunction occurs, it is necessary to turn the engine switch off to make it possible for the vehicle to recognize a new device when it is connected.

(b) Turn the engine switch on (ACC).

(c) Connect a known good USB device or "iPod" to the No. 1 stereo jack adapter assembly.

HINT:

  • If the malfunction occurred when a USB device was in use, use another USB device for the inspection. If the malfunction occurred when an "iPod" was in use, use another "iPod" for the inspection.
  • Refer to System Description for compatible formats and versions.

    Click here

NEXT

7.

CHECK USB DEVICE OR "iPod"

(a) Check if a USB device or "iPod" is recognized by the radio receiver assembly, and if information such as track, artist and album names is displayed on the screen.

OK:

USB device or "iPod" is recognized properly and the information is displayed on the screen.

OK

USB DEVICE OR "iPod" WAS INCOMPATIBLE OR DEFECTIVE
NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

    Portable Player cannot be Registered
    CAUTION / NOTICE / HINT HINT: Some versions of "Bluetooth" compatible audio players may not function properly, or the functions may be limited using the radio receiver assembly, even if the portable a ...

    Stereo Jack Adapter Light does not Illuminate
    DESCRIPTION Power is supplied to the No. 1 stereo jack adapter assembly illumination from the radio receiver assembly. WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE: Depending on the parts that are r ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Air Cooled Oil Cooler: Installation
    INSTALLATION PROCEDURE 1. INSTALL OIL COOLER BRACKET HINT: Perform this procedure only when replacement of the oil cooler bracket is necessary. (a) Install the oil cooler bracket to the vehicle body with the bolt and nut. Torque: 5.5 N·m {56 kgf·cm, 49 in·lbf} NOTICE: Tightening order: Tempor ...

    Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Power Mirror Control System (w/o Memory): AUTO Power Retract Mirrors do not operate
    DESCRIPTION The multiplex network master switch assembly sends the auto retractable outer mirror switch signal to the main body ECU (multiplex network body ECU) via LIN communication. The main body ECU (multiplex network body ECU) sends the auto retract/return signal to the outer mirror control ECU ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2024 Copyright www.lexusrx.net
    0.0206