Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual: Removal
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during trip switch removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced| Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
| Disconnect cable from negative battery terminal | Memorize steering angle neutral point | Lane Control System | |
| Pre-collision system | |||
| Intelligent clearance sonar system*1 | |||
| Parking Assist Monitor System | | ||
| Panoramic View Monitor System | | ||
| Lighting System (w/ Automatic Headlight Beam Level Control System) | | ||
| Initialize back door lock | Power door lock control system | | |
| Reset back door close position | Power Back Door System (w/ Outside Door Control Switch) | |
*1: When performing learning using the Techstream.
Click here .gif)
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
2. CHANGE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM SETTINGS
Click here
3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
4. REMOVE INSTRUMENT PANEL GARNISH LH
Click here
5. REMOVE FRONT DOOR SCUFF PLATE LH
Click here
6. REMOVE COWL SIDE TRIM BOARD LH
Click here
7. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Click here
8. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
Click here
9. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY
Click here
10. REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL
Click here
11. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL
Click here
12. REMOVE INSTRUMENT CLUSTER FINISH PANEL ORNAMENT
Click here
13. REMOVE LOWER INSTRUMENT FINISH PANEL SUB
Click here
14. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Click here
15. REMOVE TRIP SWITCH
(a) Using a screwdriver, disengage the 2 claws and remove the trip switch as shown in the illustration.
.png) | Remove in this Direction |
Inspection
INSPECTION PROCEDURE 1. INSPECT TRIP SWITCH (a) Measure the resistance according to the value(s) in the table below. Standard Resistance: Tester Connection Condition Specified Condition ...
Installation
INSTALLATION PROCEDURE 1. INSTALL TRIP SWITCH (a) Engage the 2 claws as shown in the illustration to install the trip switch. Install in this Direction 2. INSTALL INSTRUMENT CLUSTER FINISH P ...
Other materials:
Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Can Communication System: Fail-safe Chart
FAIL-SAFE CHART FAIL-SAFE FUNCTION (a) When communication fails in any of the CAN bus lines (communication lines), a fail-safe function(s) will operate. The fail-safe function that is specified for each system operates to prevent those systems from malfunctioning. (b) The following table shows the e ...
Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Panoramic View Monitor System: Camera Position Adjustment Incomplete (C1697)
DESCRIPTION This DTC is stored when the parking assist ECU judges that the camera initial setting has not been memorized (camera view adjustment is incomplete). DTC No. Detection Item DTC Detection Condition Trouble Area C1697 Camera Position Adjustment Incomplete Camera initial set ...
Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual
- For your information
- Pictorial index
- For safety and security
- Instrument cluster
- Operation of each component
- Driving
- Lexus Display Audio system
- Interior features
- Maintenance and care
- When trouble arises
- Vehicle specifications
- For owners
Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual
0.011