Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual: Removal

Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual / Vehicle Interior / Seat / Rear No. 1 Seat Assembly (for 60/40 Split Seat Type Rh Side) / Removal

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear No. 1 seat assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure	Necessary Procedures	Effect/Inoperative Function When Necessary Procedures are not Performed
Disconnect cable from negative battery terminal	Memorize steering angle neutral point	Lane Control System
		Pre-collision System
		Intelligent Clearance Sonar System*1
		Parking Assist Monitor System
		Panoramic View Monitor System
		Lighting System (w/ Automatic Headlight Beam Level Control System)
	Initialize back door lock	Power Door Lock Control System
	Reset back door close position	Power Back Door System (w/ Outside Door Control Switch)

*1: When performing learning using the Techstream.

Click here

CAUTION:

Be sure to read Precaution thoroughly before servicing.
Click here
Wear protective gloves. Sharp areas on the parts may injure your hands.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If an SRS part is accidentally deployed, it may cause a serious injury.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here

3. REMOVE REAR SEAT HEADREST ASSEMBLY

(a) Remove the rear seat headrest assembly.

4. REMOVE REAR SEAT CENTER HEADREST ASSEMBLY

(a) Remove the rear seat center headrest assembly.

5. REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

Click here

6. REMOVE SEAT INNER TRACK BRACKET COVER RH

(a) Operate the seat track adjusting handle and move the rear No. 1 seat assembly RH to the foremost position.

(b) Disengage the 7 clips and 2 guides, and remove the seat inner track bracket cover RH.

7. REMOVE REAR SEAT OUTER TRACK BRACKET COVER RH

(a) Disengage the 4 clips and guide, and remove the rear seat outer track bracket cover RH.

8. REMOVE REAR SEAT OUTER TRACK BRACKET COVER RH

(a) Operate the seat track adjusting handle and move the rear No. 1 seat assembly RH to the rearmost position.

(b) Disengage the 2 claws and 2 guides to remove the rear seat outer track bracket cover RH as shown in the illustration.

	Place Hand Here
	Remove in this Direction

9. REMOVE REAR SEAT INNER TRACK BRACKET COVER RH

HINT:

Use the same procedure as for the rear seat outer track bracket cover RH.

10. REMOVE REAR NO. 1 SEAT ASSEMBLY RH

(a) Disconnect the rear seat airbag assembly connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.

(1) Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

*a	White Housing Lock
*b	Yellow CPA
	Slide

(2) Push down the white housing lock again and disconnect the connector.

NOTICE:

Do not push the part (A) shown in the illustration when disconnecting the connector.

(b) Disconnect the connector.

(d) Operate the seat track adjusting handle and move the rear No. 1 seat assembly RH to the foremost position.

(e) Remove the 3 bolts.

(f) Disengage the 2 pins and remove the rear No. 1 seat assembly RH.

NOTICE:

Be careful not to damage the rear No. 1 seat assembly RH, vehicle body or vehicle interior.

Components

COMPONENTS ILLUSTRATION *1 REAR DOOR SCUFF PLATE RH *2 REAR NO. 1 SEAT ASSEMBLY RH *3 REAR SEAT CENTER HEADREST ASSEMBLY *4 REAR SEAT HEADREST ASSEMBLY *5 REAR SEAT INNER TRA ...

Disassembly

DISASSEMBLY CAUTION / NOTICE / HINT CAUTION: Wear protective gloves. Sharp areas on the seat frame may injure your hands. PROCEDURE 1. REMOVE SEAT ADJUSTER COVER CAP (a) Remove the 2 seat adjuster ...

Other materials:

Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Intuitive Parking Assist System (w/ Intelligent Clearance Sonar System): Front Right Center Sensor (C1AE3)
DESCRIPTION The front center ultrasonic sensor RH is installed to the front bumper. The clearance warning ECU assembly detects obstacles based on signals received from the front center ultrasonic sensor RH. If the front center ultrasonic sensor RH has an open circuit or other malfunction, it will no ...

Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Front Passenger Airbag Assembly: Installation
INSTALLATION PROCEDURE 1. INSTALL NO. 2 INSTRUMENT PANEL WIRE (a) Connect the 2 airbag connectors of the No. 2 instrument panel wire to the instrument panel passenger airbag assembly. *a Airbag Connector *b Airbag Connector Lock Wire Harness Clamp NOTICE: When connecting any ...

Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual: Removal

Components

Disassembly

Other materials:

Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual