Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual: Removal

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear seat assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Disconnect cable from negative (-) battery terminal

Memorize steering angle neutral point

Lane Control System

Pre-collision System

Intelligent Clearance Sonar System*1

Parking Assist Monitor System

Panoramic View Monitor System

Lighting System (w/ Automatic Headlight Beam Level Control System)

Initialize back door lock

Power Door Lock Control System

Reset back door close position

Power Back Door System (w/ Outside Door Control Switch)

  • Fold seat control ECU (for LH side)
  • Rear seatback frame sub-assembly LH

Initial position memorization

Rear power seat function

*1: When performing learning using the Techstream.

Click here

PROCEDURE

1. PRECAUTION

CAUTION:

  • Be sure to read Precaution thoroughly before servicing.

    Click here

  • Wear protective gloves. Sharp areas on the seat frame may injure your hands.

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here

2. REMOVE TONNEAU COVER ASSEMBLY

Click here

3. REMOVE DECK BOARD ASSEMBLY

Click here

4. REMOVE REAR SEAT HEADREST ASSEMBLY

(a) Remove the rear seat headrest assembly.

5. REMOVE REAR SEAT OUTER TRACK BRACKET COVER LH

(a) Disengage the 2 claws and 2 guides to remove the rear seat outer track bracket cover LH as shown in the illustration.

Place Hand Here

Remove in this Direction

6. REMOVE REAR SEAT INNER TRACK BRACKET COVER LH

HINT:

Use the same procedure as for the rear seat outer track bracket cover LH.

7. DISCONNECT REAR SEAT ASSEMBLY LH

(a) Using a clip remover, remove the 2 clips.

(b) Remove the bolt.

(c) Disengage the fastener to disconnect the rear seat assembly LH.

Fastener

8. DISCONNECT NO. 2 REAR SEAT RECLINING CONTROL CABLE (for Manual Seat)

(a) Lift the seat track adjusting handle and move the rear seat assembly LH to the foremost position.

(b) Pull out the lock lever to release the adjuster spring as shown in the illustration.

*a

Adjuster Spring

*b

Lock Lever

(c) Using a screwdriver with its tip wrapped with protective tape, disconnect the No. 2 rear seat reclining control cable as shown in the illustration.

*a

Protective Tape

(d) Remove the joint case from the joint case cover as shown in the illustration.

Remove in this Direction

(e) Lift and hold the No. 1 reclining adjuster release handle LH at the uppermost position as shown in the illustration.

(f) Using a screwdriver with its tip wrapped with protective tape, disconnect the No. 2 rear seat reclining control cable as shown in the illustration.

*a

Protective Tape

Remove in this Direction

(g) Using a screwdriver with its tip wrapped with protective tape, disconnect the reclining remote control lever sub-assembly RH as shown in the illustration.

*a

Protective Tape

-

-

9. REMOVE REAR SEAT ASSEMBLY LH

(a) for Power Seat:

(1) Lift the seat track adjusting handle and move the rear seat assembly LH to the foremost position.

(b) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here

(c) Disconnect the rear seat airbag assembly connector under the rear seat assembly LH.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.

(1) Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

*a

White Housing Lock

*b

Yellow CPA

Slide

(2) Push down the white housing lock again and disconnect the connector.

NOTICE:

Do not push down the part (A) shown in the illustration when disconnecting the connector.

(d) Disconnect the connector.

(e) Remove the rear center seat inner belt assembly from the rubber band of the rear seat cushion assembly RH as shown in the illustration.

*a

Rubber Band

(f) Lift the seat track adjusting handle and move the rear seat assembly LH to the foremost position.

(g) Remove the 3 bolts.

(h) Remove the 2 bolts and rear seat assembly LH.

NOTICE:

Be careful not to damage the vehicle body.

    Rear Seat Assembly (for 60/40 Split Seat Type Lh Side)
    ...

    Inspection
    INSPECTION PROCEDURE 1. PRECAUTION NOTICE: After performing the following check, initialize the fold seat control ECU (initial position reset and initial position memorization). Click here 2. INSPEC ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Automatic Light Control Sensor: On-vehicle Inspection
    ON-VEHICLE INSPECTION PROCEDURE 1. INSPECT AUTOMATIC LIGHT CONTROL SENSOR (a) Disconnect the K3 automatic light control sensor connector. *a Front view of wire harness connector (to Automatic Light Control Sensor) (b) Measure the voltage and resistance on the wire harness ...

    Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Sfi System: Dtc Check / Clear
    DTC CHECK / CLEAR NOTICE: When the diagnosis system is changed from normal mode to check mode or vice versa, all DTCs and freeze frame data recorded in normal mode are cleared. Before changing modes, always check and make a note of DTCs and freeze frame data. HINT: DTCs which are stored in the EC ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2025 Copyright www.lexusrx.net
    0.018