Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual: Removal

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear seat reclining cable removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Disconnect cable from negative battery terminal

Memorize steering angle neutral point

Lane Control System

Pre-collision System

Intelligent Clearance Sonar System*1

Parking Assist Monitor System

Panoramic View Monitor System

Lighting System (w/ Automatic Headlight Beam Level Control System)

Initialize back door lock

Power Door Lock Control System

Reset back door close position

Power Back Door System (w/ Outside Door Control Switch)

*1: When performing learning using the Techstream.

Click here

CAUTION:

  • Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

    Click here

  • Wear protective gloves. Sharp areas on the parts may injure your hands.

PROCEDURE

1. REMOVE TONNEAU COVER ASSEMBLY

Click here

2. REMOVE DECK BOARD ASSEMBLY

Click here

3. REMOVE REAR NO. 3 FLOOR BOARD

Click here

4. REMOVE REAR DECK FLOOR BOX

Click here

5. REMOVE REAR NO. 4 FLOOR BOARD

Click here

6. REMOVE FRONT DECK FLOOR BOX

Click here

7. REMOVE DECK SIDE TRIM BOX RH

Click here

8. REMOVE REAR FLOOR FINISH PLATE

Click here

9. REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

Click here

10. REMOVE REAR SEAT ASSEMBLY LH

Click here

11. REMOVE REAR SEAT ASSEMBLY RH

Click here

12. REMOVE UPPER QUARTER TRIM PAD RH

HINT:

Use the same procedure as for the LH side.

Click here

13. REMOVE REAR SEAT SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.

Click here

14. REMOVE REAR FLOOR FINISH SIDE PLATE RH

HINT:

Use the same procedure as for the LH side.

Click here

15. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

Click here

16. REMOVE ROPE HOOK ASSEMBLY

HINT:

Use the same procedure as for the LH side.

Click here

17. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY

Click here

18. REMOVE RECLINING REMOTE CONTROL BEZEL RH

Click here

19. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH

Click here

20. REMOVE RECLINING REMOTE CONTROL LEVER SUB-ASSEMBLY RH

(a) Disengage the 5 claws.

(b) Remove the 3 bolts.

(c) Disengage the guide to remove the reclining remote control lever sub-assembly RH.

    Rear Seat Reclining Control Cable
    ...

    Components
    COMPONENTS ILLUSTRATION *A for TMC Made *B for TMMC Made *1 DECK BOARD ASSEMBLY *2 DECK SIDE TRIM BOX RH *3 REAR DECK FLOOR BOX *4 REAR FLOOR FINISH PLATE *5 REAR N ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Power Mirror Control System (w/ Memory): Data List / Active Test
    DATA LIST / ACTIVE TEST DATA LIST HINT: Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be dis ...

    Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Intelligent Clearance Sonar System: G Sensor Failure (C1647)
    DESCRIPTION The clearance warning sonar ECU assembly communicates with the airbag sensor assembly*1 or yaw rate and acceleration sensor*2 via CAN communication, and if it is determined that the airbag sensor assembly*1 or yaw rate and acceleration sensor*2 is malfunctioning, DTC C1647 is stored. ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2024 Copyright www.lexusrx.net
    0.0149