Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual: Removal
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear center seat inner belt assembly removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced| Replaced Part or Performed Procedure | Necessary Procedures | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
| Disconnect cable from negative battery terminal | Memorize steering angle neutral point | Lane Control System | |
| Pre-collision system | |||
| Intelligent clearance sonar system*1 | |||
| Parking assist monitor system | | ||
| Panoramic view monitor system | | ||
| Lighting system (w/ Automatic Headlight Beam Level Control System) | | ||
| Initialize back door lock | Power door lock control system | | |
| Reset back door close position | Power Back Door System (w/ Outside Door Control Switch) | |
*1: When performing learning using the Techstream.
Click here .gif)
CAUTION:
-
Be sure to read Precaution thoroughly before servicing.
Click here
- Wear protective gloves. Sharp areas on the parts may injure your hands.
.png)
NOTICE:
After the engine switch is turned off, the radio receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) battery terminal.
PROCEDURE
1. REMOVE REAR NO. 1 SEAT ASSEMBLY RH
Click here
2. REMOVE REAR SEAT COVER CAP RH
Click here
3. REMOVE NO. 1 RECLINING ADJUSTER RELEASE HANDLE RH
Click here
4. REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH
Click here
5. REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD
Click here
6. REMOVE CENTER SEAT HINGE COVER LH
Click here
7. REMOVE REAR CENTER SEAT INNER BELT ASSEMBLY
| (a) Disconnect the connector. |
|
| (b) Disengage the guide. |
|
(c) Remove the bolt and rear center seat inner belt assembly.
Installation
INSTALLATION PROCEDURE 1. INSTALL REAR CENTER SEAT INNER BELT ASSEMBLY (a) Install the rear center seat inner belt assembly with the bolt. Torque: 42 N·m {428 kgf·cm, 31 ft·lbf} NOTICE: Do not all ...
Other materials:
Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Rear Door Window Frame Moulding: Removal
REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear door window frame moulding removal/installation are shown below. Necessary Procedures After Parts R ...
Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Front Door Speaker: Removal
REMOVAL CAUTION / NOTICE / HINT HINT:
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
PROCEDURE 1. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG Click here 2. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE ...
Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual
- For your information
- Pictorial index
- For safety and security
- Instrument cluster
- Operation of each component
- Driving
- Lexus Display Audio system
- Interior features
- Maintenance and care
- When trouble arises
- Vehicle specifications
- For owners
Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual
0.0135