Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual: Removal

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear center seat outer belt assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Disconnect cable from negative battery terminal

Memorize steering angle neutral point

Lane Control System

Pre-collision system

Intelligent clearance sonar system*1

Lighting system (w/ Automatic Headlight Beam Level Control System)

Parking assist monitor system

Panoramic view monitor system

Initialize back door lock

Power door lock control system

Reset back door close position

Power Back Door System (w/ Outside Door Control Switch)

*1: When performing learning using the Techstream.

Click here

CAUTION:

  • Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

    Click here

  • Wear protective gloves. Sharp areas on the parts may injure your hands.

NOTICE:

After the engine switch is turned off, the radio receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) battery terminal.

PROCEDURE

1. REMOVE REAR SEAT ASSEMBLY RH

Click here

2. REMOVE REAR SEAT COVER CAP RH (for Manual Seat)

Click here

3. REMOVE NO. 1 RECLINING ADJUSTER RELEASE HANDLE RH (for Manual Seat)

Click here

4. REMOVE POWER SEAT SWITCH ASSEMBLY (for Power Seat)

Click here

5. DISCONNECT SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD

Click here

6. REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD

Click here

7. DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY

(a) Remove the bolt and disconnect the anchor of the rear center seat outer belt assembly.

8. REMOVE REAR SEATBACK COVER RH

Click here

9. REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY RH

Click here

10. REMOVE SEAT BELT ANCHOR COVER CAP

Click here

11. REMOVE REAR SEAT SHOULDER BELT COVER

Click here

12. REMOVE SEPARATE TYPE REAR SEATBACK COVER WITH PAD

Click here

13. REMOVE SEATBACK FELT RH (for TMK Made)

Click here

14. REMOVE REAR CENTER SEAT OUTER BELT ASSEMBLY

(a) Remove the 2 nuts and rear center seat outer belt assembly.

    On-vehicle Inspection
    ON-VEHICLE INSPECTION CAUTION / NOTICE / HINT CAUTION: Be sure to correctly follow the removal and installation procedures for the rear center seat outer belt assembly. PROCEDURE 1. INSPECT REAR CENTE ...

    Inspection
    INSPECTION PROCEDURE 1. INSPECT REAR CENTER SEAT OUTER BELT ASSEMBLY (a) Before installing the rear center seat outer belt assembly, check the ELR function. NOTICE: Do not disassemble the retractor ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Windshield Deicer System: System Description
    SYSTEM DESCRIPTION GENERAL The windshield deicer system uses thin heater wires attached to the inside of the windshield glass to help deice the window surface more quickly. An indicator light illuminates while the system is operating. This system automatically turns off after approximately 15 minute ...

    Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Windshield Deicer System: Parts Location
    PARTS LOCATION ILLUSTRATION *1 SEMICONDUCTOR PWR INTEGRATION ECU *2 MULTI-DISPLAY ASSEMBLY - FRONT WIPER DEICER SWITCH *3 ENGINE ROOM RELAY BLOCK - ALT FUSE *4 WINDSHIELD DEICER WIRE (WINDSHIELD GLASS) *5 DLC3 *6 AIR CONDITIONING AMPLIFIER ASSEMBLY *7 INSTRUMENT P ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2024 Copyright www.lexusrx.net
    0.0204