Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual: Removal

Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual / Audio & Visual & Telematics / Audio / Video / Radio Antenna Cord (w/ Rear No. 2 Seat) / Removal

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during antenna cord sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link
*1: When performing learning using the Techstream.

Click here

Disconnect cable from negative battery terminal

Memorize steering angle neutral point

Lane Control System

Pre-collision System

Intelligent Clearance Sonar System*1

Parking Assist Monitor System

Panoramic View Monitor System

Lighting System (w/ Automatic Headlight Beam Level Control System)

Initialize back door lock

Power Door Lock Control System

Reset back door close position

Power Back Door System (w/ Outside Door Control Switch)

Removal/installation of the spiral cable with sensor sub-assembly
  • Steering angle neutral point (Initialize parking assist monitor system)
  • Steering angle setting

Parking assist monitor system

for Initialization

for Calibration

Steering angle neutral point (Initialize panoramic view monitor system)

Panoramic view monitor system

for Initialization

for Calibration

Steering angle neutral point (Initialize intelligent clearance sonar system)

Intelligent clearance sonar system

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click here

PROCEDURE

1. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

Click here

2. REMOVE NO. 4 HEATER TO REGISTER DUCT

Click here

3. REMOVE NO. 2 SIDE DEFROSTER NOZZLE DUCT

Click here

4. REMOVE ANTENNA CORD SUB-ASSEMBLY

(a) Disengage the 2 claws.

(b) Disconnect the connector.

(c) Disengage each clamp and remove the antenna cord sub-assembly.

*a

w/ Manual (SOS) Switch

-

-

5. REMOVE ROOF HEADLINING ASSEMBLY

Click here

6. REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY

(a) Remove the adhesive tape from the roof headlining assembly.

*A

for Standard Roof

*B

for Sliding Roof

*1

NO. 2 ANTENNA CORD SUB-ASSEMBLY

*2

WASHER HOSE ASSEMBLY

Adhesive Tape

Front

(b) Remove the No. 2 antenna cord sub-assembly from the roof headlining assembly.

7. REMOVE NO. 5 ANTENNA CORD SUB-ASSEMBLY (w/o Satellite Radio)

(a) Disconnect each connector.

(b) Disengage each clamp to remove the No. 5 antenna cord sub-assembly.

8. REMOVE NO. 6 ANTENNA CORD SUB-ASSEMBLY (w/ Satellite Radio)

(a) Disconnect each connector.

(b) Disengage each clamp to remove the No. 6 antenna cord sub-assembly.

9. REMOVE BACK WINDOW UPPER PANEL TRIM

Click here

10. REMOVE BACK DOOR TRIM COVER LH

Click here

11. REMOVE BACK DOOR TRIM COVER RH

HINT:

Use the same procedure as for the LH side.

12. REMOVE BACK DOOR LOCK COVER

Click here

13. REMOVE BACK DOOR TRIM BASE

Click here

14. REMOVE DOOR PULL HANDLE

Click here

15. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY

Click here

16. REMOVE BACK DOOR TRIM PANEL ASSEMBLY

Click here

17. REMOVE NO. 3 ANTENNA CORD SUB-ASSEMBLY

(a) Disconnect the 2 connectors and washer hose.

(b) Disconnect the washer hose.

(c) Disengage the 2 grommets and remove the No. 3 antenna cord sub-assembly.

18. REMOVE NO. 4 ANTENNA CORD SUB-ASSEMBLY

(a) Remove the bolt.

*a

Clamp

*b

Guide

(b) Disconnect the connector.

(c) Disengage 3 clamps and 2 guides to remove the No. 4 antenna cord sub-assembly.

    Components
    COMPONENTS ILLUSTRATION *A w/o Manual (SOS) Switch *B w/ Manual (SOS) Switch *1 ANTENNA CORD SUB-ASSEMBLY *2 NO. 2 SIDE DEFROSTER NOZZLE DUCT *3 NO. 4 HEATER TO REGISTER DUCT ...

    Installation
    INSTALLATION PROCEDURE 1. INSTALL NO. 4 ANTENNA CORD SUB-ASSEMBLY (a) Engage the 3 clamps and 2 guides. *a Clamp *b Guide (b) Connect the connector. (c) Install the ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Power Steering System: Assist Map Number Mismatch (C1582)
    DESCRIPTION When an incorrect ECM, main body ECU (multiplex network body ECU) or skid control ECU (brake actuator assembly) is installed after the assist map has been written to the power steering ECU assembly, DTC C1582 is stored because the information stored in the power steering ECU assembly doe ...

    Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Rear Power Seat Control System(for Second Row): Parts Location
    PARTS LOCATION ILLUSTRATION *1 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY - P/SEAT R/R FUSE - P/SEAT R/L FUSE *2 INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ECU-DCC NO. 2 FUSE - ECU-IG1 NO. 4 FUSE *3 MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - - ILLUSTRATION *1 ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2024 Copyright www.lexusrx.net
    0.0183