Adjustment procedure
1. To select a mirror to adjust, press the switch.
Pressing the same switch again will put the switch in neutral.
2. To adjust the mirror, press the switch.
Folding the mirrors (manual type)
Push the mirror back in the direction of the vehicle's rear.
Folding and extending the mirrors (power type)
■ Using the switch Press the switch to fold the mirrors.
Press it again to extend them to the original position.
■ Setting automatic mode Automatic mode allows the folding or extending of the mirrors to be linked to locking/unlocking of the doors.
Press the "AUTO" switch to set automatic mode.
The indicator will come on.
Pressing the switch once more will return to manual mode.
Linked mirror function when reversing
When the mirror select switch is in the "L" or "R" position, the outside rear view mirrors will automatically angle downwards when the vehicle is reversing in order to give a better view of the ground.
To disable this function, select neither "L" nor "R" of the mirror select switch.
■ Adjusting the mirror angle when the vehicle is reversing With the shift lever in R, adjust the mirror angle at a desired position.
The adjusted angle will be memorized and the mirror will automatically tilt to the memorized angle whenever the shift lever is shifted to R from next time.
The memorized downward tilt position of the mirror is linked to the normal position (angle adjusted with the shift lever in other than R). Therefore, if the normal position is changed after adjustment, the tilt position will also change.
When the normal position is changed, readjust the angle in reversing.
■ Mirror angle can be adjusted when The power switch is in ACCESSORY or ON mode.
■ When disconnecting and reconnecting 12-volt battery terminals (power type) The automatic folding/extending mirror function will return to off as default. To turn the function on, press the switch again to select on.
■ When the mirrors are fogged up The outside rear view mirrors can be cleared using the mirror defoggers. Turn on the rear window defogger to turn on the outside rear view mirror defoggers.
■ Automatic adjustment of the mirror angle (if equipped) A desired mirror face angle can be entered to memory and recalled automatically by the driving position memory.
■ Auto anti-glare function (if equipped) When the anti-glare inside rear view mirror is set to automatic mode, the outside rear view mirrors will activate in conjunction with the anti-glare inside rear view mirror to reduce reflected light.
■ Using automatic mode in cold weather (if equipped) When automatic mode is used in cold weather, the door mirror could freeze up and automatic stowing and return may not be possible. In this case, remove any ice and snow from the door mirror, then either operate the mirror using manual mode or move the mirror by hand.
■ Customization Some functions can be customized.
WARNING
■ Important points while driving Observe the following precautions while driving.
Failing to do so may result in loss of control of the vehicle and cause an accident, resulting in death or serious injury.
■When a mirror is moving To avoid personal injury and mirror malfunction, be careful not to get your hand caught by the moving mirror.
■ When the mirror defoggers are operating Do not touch the rear view mirror surfaces, as they can become very hot and burn you.
Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Lighting System (w/ Automatic Headlight Beam Level Control System): Lost Communication With Headlamp Control Module "B" (U0242)
DESCRIPTION for Multiple Beam Headlight:
The No. 1 headlight ECU sub-assembly LH communicates with the No. 1 headlight ECU sub-assembly RH via CAN communication. If communication between the No. 1 headlight ECU sub-assembly LH and No. 1 headlight ECU sub-assembly RH stops, the No. 1 headlight ECU ...
Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Smart Access System With Push-button Start (for Start Function): Vehicle Speed Signal Malfunction (B2282,B2283)
DESCRIPTION DTC B2282 is stored when the vehicle speed signal sent by the combination meter assembly via direct line and the vehicle speed signal sent via CAN communication do not match. DTC B2283 is stored when a malfunction in the vehicle speed sensor is detected. DTC No. Detection Item DTC ...