CAUTION / NOTICE / HINT
HINT:
PROCEDURE
1. | VEHICLE BROUGHT TO WORKSHOP |
|
2. | CUSTOMER PROBLEM ANALYSIS |
(a) Ask the customer about the problems and the conditions at the time the malfunction occurred to make sure the problem symptom was not temporarily caused by radio waves in the surrounding environment.
HINT:
The parking assist monitor display may be temporarily distorted due to radio waves around the vehicle.
Problem Symptom | Cause |
---|---|
The problem symptom indicates a parking assist monitor display malfunction and the problem symptom cannot be reproduced. | The display may be temporarily distorted when the vehicle is close to an object that transmits radio waves, such as a telecommunication tower, an airport or a truck equipped with a transceiver. |
|
3. | INSPECT BATTERY VOLTAGE |
(a) Measure the battery voltage.
Standard Voltage:
11 to 14 V
If the voltage is below 11 V, replace or recharge the battery before proceeding to the next step.
|
4. | SYSTEM CHECK |
(a) Check the vehicle specification.
Result | Proceed to |
---|---|
w/ Navigation System | A |
w/ Audio and Visual System | B |
B | ![]() | GO TO STEP 6 |
|
5. | CHECK NAVIGATION SYSTEM |
(a) Refer to the navigation system.
Click here
Result | Proceed to |
---|---|
Navigation system is normal | A |
Navigation system is abnormal | B |
A | ![]() | GO TO STEP 7 |
B | ![]() | GO TO NAVIGATION SYSTEM |
6. | CHECK AUDIO AND VISUAL SYSTEM |
(a) Refer to audio and visual system.
for 8 Inch Display:
Click here
for 12.3 Inch Display:
Click here
Result | Proceed to |
---|---|
Audio and visual system is normal | A |
Audio and visual system is abnormal | B |
B | ![]() | GO TO AUDIO AND VISUAL SYSTEM |
|
7. | CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM* |
(a) Use the Techstream to check if the CAN communication system is functioning normally.
Click here
Result | Proceed to |
---|---|
CAN DTCs are not output | A |
CAN DTCs are output | B |
B | ![]() | GO TO CAN COMMUNICATION SYSTEM |
|
8. | CHECK FOR DTC (PARKING ASSIST MONITOR SYSTEM)* |
(a) Check for DTCs and note any codes that are output.
Click here
(b) Clear the DTCs.
Click here
(c) Recheck for DTCs. Try to prompt the DTC by simulating the original activity that the DTC suggests.
Click here
NOTICE:
The radio receiver assembly outputs DTCs for the following systems. When DTCs other than those in Diagnostic Trouble Code Chart for the parking assist monitor system are output, refer to Diagnostic Trouble Code Chart for the relevant systems.
Refer to navigation system*1.
Click here
Refer to audio and visual system (for 8 Inch Display)*2.
Click here
Refer to audio and visual system (for 12.3 Inch Display)*2.
Click here
Result | Proceed to |
---|---|
No DTCs are output | A |
DTCs for parking assist monitor system are output | B |
DTCs for navigation system*1 are output | C |
DTCs for audio and visual system*2 are output | D |
*1: w/ Navigation System
*2: w/ Audio and Visual System
B | ![]() | GO TO DIAGNOSTIC TROUBLE CODE CHART |
C | ![]() | GO TO NAVIGATION SYSTEM |
D | ![]() | GO TO AUDIO AND VISUAL SYSTEM |
|
9. | PROBLEM SYMPTOMS TABLE |
(a) Refer to the Problem Symptoms Table.
Click here
Result | Proceed to |
---|---|
Fault is not listed in Problem Symptoms Table | A |
Fault is listed in Problem Symptoms Table | B |
B | ![]() | GO TO STEP 11 |
|
10. | OVERALL ANALYSIS AND TROUBLESHOOTING* |
(a) Diagnosis System.
Click here
(b) Terminals of ECU.
Click here
(c) Data List / Active Test.
Click here
|
11. | ADJUST, REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE |
|
12. | CONFIRMATION TEST |
NEXT | ![]() | END |
Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Steering Lock System: Parts Location
PARTS LOCATION ILLUSTRATION *1 FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH *2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY - IG2 RELAY - IG2-MAIN FUSE - ECU-IG2 NO. 1 FUSE ILLUSTRATION *1 MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) *2 ID CODE BOX (IMMOBILISER CODE ECU) ...
Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Can Communication System: Restraints Occupant Classification System Module Communication Stop Mode
DESCRIPTION Detection Item Symptom Trouble Area Restraints Occupant Classification System Module Communication Stop Mode Either condition is met:
"Occupant Detection" is not displayed on the CAN Bus Check screen of the Techstream.
Click here
Communication system DTCs (DTCs tha ...