COMPONENTS
ILLUSTRATION
*1 | AUTOMATIC TRANSMISSION ASSEMBLY | *2 | TRANSFER AND TRANSAXLE SETTING STUD BOLT |
*3 | TRANSFER ASSEMBLY | - | - |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part | |
★ | Precoated part | - | - |
ILLUSTRATION
*1 | TRANSFER AND TRANSAXLE SETTING STUD BOLT | *2 | TRANSFER EXTENSION HOUSING SUB-ASSEMBLY |
*3 | TRANSFER EXTENSION HOUSING TYPE T OIL SEAL | *4 | TRANSFER CASE OIL SEAL |
*5 | TRANSFER CASE OIL SEAL RH | *6 | TRANSFER CASE STRAIGHT PIN |
*7 | REAR TRANSFER DRIVEN PINION BEARING | *8 | TRANSFER EXTENSION HOUSING DUST DEFLECTOR |
*9 | FILLER PLUG (NO. 1 TRANSFER CASE PLUG) | *10 | NO. 2 TRANSFER CASE PLUG |
*11 | TRANSFER DRAIN PLUG | *12 | GASKET |
*13 | GEAR NUT | *14 | REAR TRANSFER DRIVEN PINION BEARING (INNER RACE) |
*15 | REAR TRANSFER DRIVEN PINION BEARING (OUTER RACE) | - | - |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | N*m (kgf*cm, ft.*lbf): Specified torque | ||
* | For use with SST | ● | Non-reusable part |
MP grease | Hypoid Gear Oil LSD | ||
★ | Precoated part | - | - |
ILLUSTRATION
*1 | BEARING CAP | *2 | BREATHER OIL DEFLECTOR |
*3 | DRIVEN PINION | *4 | FRONT TRANSFER DRIVEN PINION BEARING |
*5 | NO. 1 TRANSFER OUTPUT SHAFT SPACER | *6 | NO. 2 TRANSFER RING GEAR MOUNTING CASE WASHER |
*7 | RING GEAR | *8 | RING GEAR MOUNTING CASE BEARING (for RH side) |
*9 | RING GEAR MOUNTING CASE BEARING (for LH side) | *10 | TRANSFER CASE BREATHER PLUG |
*11 | TRANSFER CASE COVER SUB-ASSEMBLY | *12 | TRANSFER CASE STRAIGHT PIN |
*13 | TRANSFER OUTPUT SHAFT WASHER | *14 | TRANSFER RING GEAR MOUNTING CASE |
*15 | RING GEAR MOUNTING CASE PLATE WASHER | *16 | TRANSFER PINION BEARING SPACER |
*17 | TRANSFER CASE SUB-ASSEMBLY | *18 | RING GEAR MOUNTING CASE BEARING (INNER RACE) |
*19 | RING GEAR MOUNTING CASE BEARING (OUTER RACE) | *20 | FRONT TRANSFER DRIVEN PINION BEARING (INNER RACE) |
*21 | FRONT TRANSFER DRIVEN PINION BEARING (OUTER RACE) | - | - |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | N*m (kgf*cm, ft.*lbf): Specified torque | ||
● | Non-reusable part | Adhesive 1324 | |
★ | Precoated part | - | - |
Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Steering Column Assembly: Removal
REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the electric power steering column sub-assembly removal/installation are shown below. Necessary Procedure ...
Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Mass Air Flow Meter: Removal
REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during mass air flow meter sub-assembly removal/installation are shown below. Necessary Procedures After Parts ...