DESCRIPTION
The ATF temperature sensor converts the automatic transaxle fluid (ATF) temperature into a resistance value for use by the ECM.
The ECM applies voltage to the temperature sensor through terminal THO1 of the ECM.
The sensor resistance changes with the ATF temperature. As the temperature rises, the sensor resistance decreases.
One terminal of the sensor is grounded so that the sensor resistance and voltage decrease as the temperature rises.
The ECM calculates the ATF temperature based on the voltage signal.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
---|---|---|---|---|---|---|
P071011 | Transmission Fluid Temperature Sensor "A" Circuit Short To Ground | 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
|
| Comes on | DTC stored | SAE Code: P0712 |
MONITOR DESCRIPTION
This DTC indicates a short to ground in the ATF temperature sensor circuit. The ATF temperature sensor converts the ATF temperature into an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature, and can detect a short to ground in the ATF temperature sensor circuit. If the resistance value of the ATF temperature sensor is below 79 Ω*, the ECM interprets this as a malfunction of the ATF temperature sensor or in the wire harness, illuminates the MIL and stores this DTC.
*: 150°C (302°F) or higher is indicated regardless of the actual ATF temperature.
HINT:
The ATF temperature can be checked in the Data List.
MONITOR STRATEGY
Related DTCs | P0712: ATF temperature sensor/Range check (Low voltage) |
Required sensors/Components | ATF temperature sensor (TFT sensor) |
Frequency of operation | Continuous |
Duration | 0.5 sec. |
MIL operation | Immediate |
Sequence of operation | None |
TYPICAL ENABLING CONDITIONS
The monitor will run whenever these DTCs are not present | None |
Battery voltage | 8 V or more |
Engine switch | On (IG) |
Starter | OFF |
TYPICAL MALFUNCTION THRESHOLDS
TFT sensor voltage (ATF temperature) | Less than 0.142 V (More than 164°C (327°F)) |
COMPONENT OPERATING RANGE
ATF temperature sensor (TFT sensor) resistance | 79 to 156 kΩ |
CONFIRMATION DRIVING PATTERN
HINT:
Click here
HINT:
[*1] : Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
Techstream Display | Description |
---|---|
NORMAL |
|
ABNORMAL |
|
INCOMPLETE |
|
N/A |
|
HINT:
WIRING DIAGRAM
Refer to DTC P071000.
Click here
CAUTION / NOTICE / HINT
NOTICE:
Click here
Click here
DATA LIST
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
(a) Warm up the engine.
(b) Turn the engine switch off.
(c) Connect the Techstream to the DLC3.
(d) Turn the engine switch on (IG).
(e) Turn the Techstream on.
(f) Enter the following menus: Powertrain / Transmission / Data List / A/T Oil Temperature No.1.
(g) Read the Data List according to the display on the Techstream.
Powertrain > Transmission > Data List Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
---|---|---|---|---|
A/T Oil Temperature No.1 | ATF temperature sensor value | Min.: -40°C (-40°F) Max.: 150°C (302°F) |
| If value is -40°C (-40°F) or 150°C (302°F), ATF temperature sensor circuit is open or shorted |
Tester Display |
---|
A/T Oil Temperature No.1 |
HINT:
Check the temperature displayed on the Techstream in order to check if a malfunction exists.
Temperature Displayed | Malfunction |
---|---|
-40°C (-40°F) | Open circuit |
150°C (302°F) or higher | Short circuit |
PROCEDURE
1. | READ VALUE USING TECHSTREAM |
(a) Warm up the engine.
(b) Turn the engine switch off.
(c) Connect the Techstream to the DLC3.
(d) Turn the engine switch on (IG).
(e) Turn the Techstream on.
(f) Enter the following menus: Powertrain / Transmission / Data List / A/T Oil Temperature No.1.
(g) Read the Data List according to the display on the Techstream.
Powertrain > Transmission > Data List Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
---|---|---|---|---|
A/T Oil Temperature No.1 | ATF temperature sensor value | Min.: -40°C (-40°F) Max.: 150°C (302°F) |
| If value is -40°C (-40°F) or 150°C (302°F), ATF temperature sensor circuit is open or shorted |
Tester Display |
---|
A/T Oil Temperature No.1 |
Result | Proceed to |
---|---|
Data List value is normal | A |
Data List value is not normal | B |
A | ![]() | GO TO STEP 3 |
|
2. | CHECK HARNESS AND CONNECTOR (ATF TEMPERATURE SENSOR - ECM) |
(a) Disconnect the D2 ECM connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
---|---|---|
D2-86 (THO1) - D2-133 (ETHW) | Always | 79 Ω to 156 kΩ |
D2-133 (ETHW) - Body ground | Always | 10 kΩ or higher |
D2-86 (THO1) - Body ground | Always | 10 kΩ or higher |
HINT:
If the resistance is out of the specified range at any of the ATF temperatures shown in the table below, the driveability of the vehicle may decrease.
ATF Temperature | Specified Condition |
---|---|
10°C (50°F) | 5 to 8 kΩ |
25°C (77°F) | 2.5 to 4.5 kΩ |
110°C (230°F) | 0.22 to 0.28 kΩ |
NG | ![]() | GO TO STEP 4 |
|
3. | REPLACE ECM |
(a) Replace the ECM.
Click here
NEXT | ![]() | PERFORM A/T CODE REGISTRATION |
4. | CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM) |
(a) Disconnect the D56 transmission wire connector.
(b) Disconnect the D2 ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
---|---|---|
D56-8 (OIL) or D2-86 (THO1) - Body ground | Always | 10 kΩ or higher |
D56-9 (E2) or D2-133 (ETHW) - Body ground | Always | 10 kΩ or higher |
OK | ![]() | REPLACE TRANSMISSION WIRE (ATF TEMPERATURE SENSOR) |
NG | ![]() | REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM) |
Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Rear Differential Side Gear Shaft Oil Seal: Replacement
REPLACEMENT CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear drive shaft oil seal replacement are shown below. Necessary Procedures After Parts Removed/Ins ...
Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Navigation System: NTSC Disconnected (from Park Assist/Monitoring ECU) (B1535,C1622)
DESCRIPTION These DTCs are stored if the radio receiver assembly judges that the signals or signal lines between the rear television camera assembly and the multi-display assembly are not normal as a result of its self check. DTC No. Detection Item DTC Detection Condition Trouble Area B ...