Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual: Random/Multiple Cylinder Misfire Detected (P030000,P030027,P030085-P030600)

Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual / Engine & Hybrid System / 2gr-fks (engine Control) / Sfi System / Random/Multiple Cylinder Misfire Detected (P030000,P030027,P030085-P030600)

DESCRIPTION

When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high hydrocarbon concentration levels can cause an increase in exhaust emission levels. Extremely high concentrations of hydrocarbons can also cause increases in the three-way catalytic converter temperature, which may cause damage to the three-way catalytic converter. To prevent this increase in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire count. When the temperature of the three-way catalytic converter reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the VVT sensor and the crankshaft position sensor. The VVT sensor is used to identify any misfiring cylinders and the crankshaft position sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted when the crankshaft rotation speed variations exceed predetermined thresholds. If the misfire count exceeds the threshold levels, and could cause emission control system performance deterioration, the ECM illuminates the MIL and stores a DTC.

DTC No.	Detection Item	DTC Detection Condition	Trouble Area	MIL	Memory	Note
P030000	Random/Multiple Cylinder Misfire Detected	Simultaneous misfiring of several cylinders occurs and one of the following conditions is met (2 trip detection logic): A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected). An emission deterioration misfire occurs (MIL illuminates).	Open or short in engine wire harness Connector connection Vacuum hose connections Ignition system Fuel injector assembly (for port injection) Fuel injector assembly (for direct injection) Fuel pressure Mass air flow meter sub-assembly Engine coolant temperature sensor Compression pressure Valve timing PCV valve and hose PCV hose connections Intake system ECM	Comes on/Blinks* *: The MIL flashes when a catalyst-damaging misfire is detected.	DTC stored	SAE Code: P0300
P030027	Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold	An emission deterioration misfire occurs (2 trip detection logic).	Open or short in engine wire harness Connector connection Vacuum hose connections Ignition system Fuel injector assembly (for port injection) Fuel injector assembly (for direct injection) Fuel pressure Mass air flow meter sub-assembly Engine coolant temperature sensor Compression pressure Valve timing PCV valve and hose PCV hose connections Intake system ECM	Comes on	DTC stored	SAE Code: -
P030085	Random / Multiple Cylinder Misfire Detected (Over Temperature) Signal Above Allowable Range	A misfire occurs that may damage the three-way catalytic converter (2 trip detection logic).	Open or short in engine wire harness Connector connection Vacuum hose connections Ignition system Fuel injector assembly (for port injection) Fuel injector assembly (for direct injection) Fuel pressure Mass air flow meter sub-assembly Engine coolant temperature sensor Compression pressure Valve timing PCV valve and hose PCV hose connections Intake system ECM	Comes on/Blinks* *: The MIL flashes when a catalyst-damaging misfire is detected.	DTC stored	SAE Code: -
P030100	Cylinder 1 Misfire Detected	Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic): A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected). An emission deterioration misfire occurs (MIL illuminates).	Open or short in engine wire harness Connector connection Vacuum hose connections Ignition system Fuel injector assembly (for port injection) Fuel injector assembly (for direct injection) Fuel pressure Mass air flow meter sub-assembly Engine coolant temperature sensor Compression pressure Valve timing PCV valve and hose PCV hose connections Intake system ECM	Comes on/Blinks* *: The MIL flashes when a catalyst-damaging misfire is detected.	DTC stored	SAE Code: P0301
P030200	Cylinder 2 Misfire Detected	Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic): A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected). An emission deterioration misfire occurs (MIL illuminates).	Open or short in engine wire harness Connector connection Vacuum hose connections Ignition system Fuel injector assembly (for port injection) Fuel injector assembly (for direct injection) Fuel pressure Mass air flow meter sub-assembly Engine coolant temperature sensor Compression pressure Valve timing PCV valve and hose PCV hose connections Intake system ECM	Comes on/Blinks* *: The MIL flashes when a catalyst-damaging misfire is detected.	DTC stored	SAE Code: P0302
P030300	Cylinder 3 Misfire Detected	Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic): A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected). An emission deterioration misfire occurs (MIL illuminates).	Open or short in engine wire harness Connector connection Vacuum hose connections Ignition system Fuel injector assembly (for port injection) Fuel injector assembly (for direct injection) Fuel pressure Mass air flow meter sub-assembly Engine coolant temperature sensor Compression pressure Valve timing PCV valve and hose PCV hose connections Intake system ECM	Comes on/Blinks* *: The MIL flashes when a catalyst-damaging misfire is detected.	DTC stored	SAE Code: P0303
P030400	Cylinder 4 Misfire Detected	Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic): A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected). An emission deterioration misfire occurs (MIL illuminates).	Open or short in engine wire harness Connector connection Vacuum hose connections Ignition system Fuel injector assembly (for port injection) Fuel injector assembly (for direct injection) Fuel pressure Mass air flow meter sub-assembly Engine coolant temperature sensor Compression pressure Valve timing PCV valve and hose PCV hose connections Intake system ECM	Comes on/Blinks* *: The MIL flashes when a catalyst-damaging misfire is detected.	DTC stored	SAE Code: P0304
P030500	Cylinder 5 Misfire Detected	Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic): A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected). An emission deterioration misfire occurs (MIL illuminates).	Open or short in engine wire harness Connector connection Vacuum hose connections Ignition system Fuel injector assembly (for port injection) Fuel injector assembly (for direct injection) Fuel pressure Mass air flow meter sub-assembly Engine coolant temperature sensor Compression pressure Valve timing PCV valve and hose PCV hose connections Intake system ECM	Comes on/Blinks* *: The MIL flashes when a catalyst-damaging misfire is detected.	DTC stored	SAE Code: P0305
P030600	Cylinder 6 Misfire Detected	Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic): A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected). An emission deterioration misfire occurs (MIL illuminates).	Open or short in engine wire harness Connector connection Vacuum hose connections Ignition system Fuel injector assembly (for port injection) Fuel injector assembly (for direct injection) Fuel pressure Mass air flow meter sub-assembly Engine coolant temperature sensor Compression pressure Valve timing PCV valve and hose PCV hose connections Intake system ECM	Comes on/Blinks* *: The MIL flashes when a catalyst-damaging misfire is detected.	DTC stored	SAE Code: P0306

When DTCs for misfiring cylinders are randomly stored, but DTC P030000 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P030000 is only stored when several misfiring cylinders are detected at the same time.

MONITOR DESCRIPTION

The ECM illuminates the MIL and stores a DTC when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).

Within the first 1000 crankshaft revolutions after the engine starts, an excessive number of misfires (approximately 50 to 100 misfires per 1000 crankshaft revolutions) occurs once.
An excessive number of misfires (approximately 50 to 100 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.

The ECM flashes the MIL (immediate detection logic) and stores a DTC (2 trip detection logic) when either one of the following conditions, which could cause damage to the three-way catalytic converter, is detected.

At a high engine speed, a sufficient amount of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected once.
At a normal engine speed, a sufficient amount of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected 3 times.

MONITOR STRATEGY

Related DTCs	P0300: Multiple cylinder misfire P0301: Cylinder 1 misfire P0302: Cylinder 2 misfire P0303: Cylinder 3 misfire P0304: Cylinder 4 misfire P0305: Cylinder 5 misfire P0306: Cylinder 6 misfire
Required Sensors/Components (Main)	Crankshaft position sensor VVT sensor
Required Sensors/Components (Related)	Engine coolant temperature Intake air temperature sensor (mass air flow meter sub-assembly) Mass air flow meter sub-assembly
Frequency of Operation	Continuous
Duration	1000 crankshaft revolutions (soon after engine is started: 1 time, other 4 times) (Emission-related misfire) 200 crankshaft revolutions (1 or 3 times) (Catalyst-damaging misfire)
MIL Operation	2 driving cycles: Emission-related misfire MIL flashes immediate: Catalyst-damaging misfire
Sequence of Operation	None

TYPICAL ENABLING CONDITIONS

Misfire

Monitor runs whenever the following DTCs are not stored	P0016, P0018 (VVT system bank 1, 2 - misalignment) P0017, P0019 (Exhaust VVT system bank 1, 2 - misalignment) P0101, P0102, P0103 (Mass air flow meter) P0112, P0113 (Intake air temperature sensor) P0117, P0118 (Engine coolant temperature sensor) P0121, P0122, P0123, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0327, P0328, P0332, P0333 (Knock control sensor) P0335, P0337, P0338 (Crankshaft position sensor) P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor) P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor) P0500 (Vehicle speed sensor) P0705 (Shift lever position switch)
Battery voltage	8 V or higher
VVT system	Not operated by scan tool
Engine speed	400 to 6500 rpm
Either of the following conditions is met	(a) or (b)
(a) Engine coolant temperature at engine start	Higher than -7°C (19°F)
(b) Engine coolant temperature	Higher than 20°C (68°F)
Fuel cut	Off

Monitor Period of Emission-related Misfire

First 1000 revolutions after engine start, or during check mode	Crankshaft 1000 revolutions
Except above	Crankshaft 1000 revolutions x 4

Monitor Period of Catalyst-damaging Misfire (MIL Blinks)

All of the following conditions 1, 2, 3 and 4 are met	Crankshaft 200 revolutions x 3
Except above (MIL blinks immediately)	Crankshaft 200 revolutions
1. Driving cycles	1st
2. Check mode	Off
3. Engine speed	Less than 2050 rpm
4. Engine load	Less than 57%

TYPICAL MALFUNCTION THRESHOLDS

Monitor Period of Emission-related Misfire

Misfire rate

2.4375% or higher (w/o Rear No. 2 Seat)

2.8594% or higher (w/ Rear No. 2 Seat)

Monitor Period of Catalyst-damaging Misfire (MIL Blinks)

Number of misfires per 200 revolutions

103 or more (varies with engine speed and engine load)

MONITOR RESULT

Refer to detailed information in Checking Monitor Status.

Click here

P0300: Misfire / EWMA MISFIRE

Monitor ID	Test ID	Scaling	Unit	Description
$A1	$0B	Multiply by 1	Count	Total EWMA* misfire count of all cylinders in last ten driving cycles

P0300: Misfire / MISFIRE RATE

Monitor ID	Test ID	Scaling	Unit	Description
$A1	$0C	Multiply by 1	Count	When engine switch on (IG), total misfire count of all cylinders in last driving cycle is displayed. While engine is running, total misfire count of all cylinders in current driving cycle is displayed.

P0301: Misfire / EWMA MISFIRE1

Monitor ID	Test ID	Scaling	Unit	Description
$A2	$0B	Multiply by 1	Count	Total EWMA* misfire count of cylinder 1 in last ten driving cycles

P0301: Misfire / MISFIRE RATE1

Monitor ID	Test ID	Scaling	Unit	Description
$A2	$0C	Multiply by 1	Count	When engine switch on (IG), total misfire count of cylinder 1 in last driving cycle is displayed. While engine is running, total misfire count of cylinder 1 in current driving cycle is displayed.

P0302: Misfire / EWMA MISFIRE2

Monitor ID	Test ID	Scaling	Unit	Description
$A3	$0B	Multiply by 1	Count	Total EWMA* misfire count of cylinder 2 in last ten driving cycles

P0302: Misfire / MISFIRE RATE2

Monitor ID	Test ID	Scaling	Unit	Description
$A3	$0C	Multiply by 1	Count	When engine switch on (IG), total misfire count of cylinder 2 in last driving cycle is displayed. While engine is running, total misfire count of cylinder 2 in current driving cycle is displayed.

P0303: Misfire / EWMA MISFIRE3

Monitor ID	Test ID	Scaling	Unit	Description
$A4	$0B	Multiply by 1	Count	Total EWMA* misfire count of cylinder 3 in last ten driving cycles

P0303: Misfire / MISFIRE RATE3

Monitor ID	Test ID	Scaling	Unit	Description
$A4	$0C	Multiply by 1	Count	When engine switch on (IG), total misfire count of cylinder 3 in last driving cycle is displayed. While engine is running, total misfire count of cylinder 3 in current driving cycle is displayed.

P0304: Misfire / EWMA MISFIRE4

Monitor ID	Test ID	Scaling	Unit	Description
$A5	$0B	Multiply by 1	Count	Total EWMA* misfire count of cylinder 4 in last ten driving cycles

P0304: Misfire / MISFIRE RATE4

Monitor ID	Test ID	Scaling	Unit	Description
$A5	$0C	Multiply by 1	Count	When engine switch on (IG), total misfire count of cylinder 4 in last driving cycle is displayed. While engine is running, total misfire count of cylinder 4 in current driving cycle is displayed.

P0305: Misfire / EWMA MISFIRE5

Monitor ID	Test ID	Scaling	Unit	Description
$A6	$0B	Multiply by 1	Count	Total EWMA* misfire count of cylinder 5 in last ten driving cycles

P0305: Misfire / MISFIRE RATE5

Monitor ID	Test ID	Scaling	Unit	Description
$A6	$0C	Multiply by 1	Count	When engine switch on (IG), total misfire count of cylinder 5 in last driving cycle is displayed. While engine is running, total misfire count of cylinder 5 in current driving cycle is displayed.

P0306: Misfire / EWMA MISFIRE6

Monitor ID	Test ID	Scaling	Unit	Description
$A7	$0B	Multiply by 1	Count	Total EWMA* misfire count of cylinder 6 in last ten driving cycles

P0306: Misfire / MISFIRE RATE6

Monitor ID	Test ID	Scaling	Unit	Description
$A7	$0C	Multiply by 1	Count	When engine switch on (IG), total misfire count of cylinder 6 in last driving cycle is displayed. While engine is running, total misfire count of cylinder 6 in current driving cycle is displayed.

HINT:

*: EWMA (Exponential Weighted Moving Average) misfire counts for last 10 driving cycles (calculated) Calculation: 0.1 x (current counts) + 0.9 x (previous average)

Initial value for (previous average) = 0

CONFIRMATION DRIVING PATTERN

HINT:

When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
Permanent misfire and fuel system DTCs can only be cleared when performing the universal trip driving pattern when no malfunction is detected.

Connect the Techstream to the DLC3.
Turn the engine switch on (IG).
Turn the Techstream on.
Record the DTC(s) and freeze frame data.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Using the Techstream, switch the ECM from normal mode to check mode.
Click here
Start the engine.
Read the misfire counts of each cylinder, Misfire Count Cylinder #1 to Misfire Count Cylinder #6, with the engine idling. If any misfire count is displayed, skip the following confirmation driving pattern.
Drive the vehicle so that the vehicle conditions displayed in Misfire RPM and Misfire Load of the Data List are the same as the freeze frame data. Perform this step several times.
HINT:

In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, confirm the Misfire RPM and Misfire Load in the Data List.

Engine speed

Duration

Idling

8.0 minutes or more

1000

4.5 minutes or more

2000

2.5 minutes or more

3000

1.5 minutes or more
Check whether misfires have occurred by checking DTCs and freeze frame data.
HINT:

Do not turn the engine switch off until the output DTC(s) and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), freeze frame data and other data are cleared.
Record the DTC(s), freeze frame data and misfire counts.
Turn the engine switch off and wait for at least 30 seconds.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

Engine speed	Duration
Idling	8.0 minutes or more
1000	4.5 minutes or more
2000	2.5 minutes or more
3000	1.5 minutes or more

WIRING DIAGRAM

Refer to DTC P010012 for the mass air flow meter sub-assembly circuit.

Click here

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.

HINT:

If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.
Check the "Fuel Cut Elapsed Time" in the Data List or the Freeze Frame Data.
If the elapsed time is over 0 seconds, then the engine speed is high (engine speed at which fuel cut occurs + 500 rpm).

When this has happened, there is the possibility that the No. 1 valve rocker arm sub-assembly will become loose and a fire could start, so check that the No. 1 valve rocker arm sub-assembly is properly attached.
By clearing the DTCs, "Fuel Cut Elapsed Time" will be cleared.
If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the ECM as freeze frame data.
If the misfire still cannot be reproduced even though the conditions stored in the ECM as freeze frame data have been reproduced, one of the following factors is considered to be a possible cause of the problem:
1. There was insufficient fuel in the tank.
2. Improper fuel was used.
3. The spark plugs have been contaminated.
4. The problem requires further diagnosis.
After finishing repairs, check the misfire counts of the cylinders (Misfire Count Cylinder #1 to Misfire Count Cylinder #6).
Be sure to confirm that no misfiring cylinder DTCs are stored again by performing the confirmation driving pattern after finishing repairs.
For 6 cylinder engine, the ECM intentionally does not set the specific misfiring cylinder DTCs at high engine speed. If misfires occur only in high engine speed areas, only DTC P030000 is set.
In the event of DTC P030000 being present, perform the following operations:
1. Clear the DTCs.
  Click here
2. Start the engine and conduct the confirmation driving pattern.
3. Read the misfire count of each cylinder or DTC(s) using the Techstream.
4. Repair the cylinder(s) that has a high misfiring count or is indicated by the DTC.
5. After finishing repairs, conduct the confirmation driving pattern again, in order to verify that DTC P030000 is not set.
When one of Short FT B1S1, Long FT B1S1, Short FT B2S1 or Long FT B2S1 in the freeze frame data is outside the range of +/-20%, the air fuel ratio may be rich (-20% or less) or lean (20% or higher).
When Coolant Temperature in the freeze frame data is less than 75°C (167°F), the misfires have occurred only while warming up the engine.
Vehicle body vibration caused by an extremely imbalanced drive wheel may cause misfire DTCs to be stored.
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

1.	CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE DTCS)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(d) Enter the following menus: Powertrain / Engine / Trouble Codes.

(e) Read the DTCs.

Powertrain > Engine > Trouble Codes

Result	Proceed to
DTC P030000, P030027, P030085, P030100, P030200, P030300, P030400, P030500 and/or P030600 are output	A
DTC P030000, P030027, P030085, P030100, P030200, P030300, P030400, P030500 and/or P030600 and other DTCs are output	B

HINT:

If any DTCs other than P030000, P030027, P030085, P030100, P030200, P030300, P030400, P030500 and/or P030600 are output, troubleshoot those DTCs first.

GO TO DTC CHART

2.	CHECK PCV HOSE CONNECTIONS

(a) Check the PCV hose connections.

Click here

OK:

PCV valve and hose are correctly connected and are not damaged.

REPAIR OR REPLACE PCV HOSE

3.	READ VALUE USING TECHSTREAM (MISFIRE RPM AND MISFIRE LOAD)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(d) Enter the following menus: Powertrain / Engine / Data List / Misfire RPM and Misfire Load.

Powertrain > Engine > Data List

Tester Display
Misfire RPM
Misfire Load

(e) Read and note the Misfire RPM and Misfire Load values.

HINT:

The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.

4.	READ VALUE USING TECHSTREAM (CATALYST OT MISFIRE FUEL CUT)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(d) Enter the following menus: Powertrain / Engine / Data List / Catalyst OT Misfire Fuel Cut.

Powertrain > Engine > Data List

Tester Display
Catalyst OT Misfire Fuel Cut

(e) Read the value displayed on the Techstream.

Data List	Result	Proceed to
Catalyst OT Misfire Fuel Cut	Avail	A
Catalyst OT Misfire Fuel Cut	Not Avl	B

GO TO STEP 7

5.	READ FREEZE FRAME DATA (CATALYST OT MISFIRE FUEL CUT HISTORY)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(d) Using the Techstream, confirm the vehicle conditions recorded in the Freeze Frame Data which were present when the DTC was stored.

Click here

Freeze Frame Data Item	Result	Proceed to
Catalyst OT Misfire Fuel Cut History	ON	A
Catalyst OT Misfire Fuel Cut History	OFF	B

GO TO STEP 7

6.	CHECK MISFIRE COUNT OF PORT INJECTION

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(d) Start the engine and warm it up.

(e) Enter the following menus: Powertrain / Engine / Active Test / Prohibit the Catalyst OT Misfire Prevent Fuel Cut / Data List / Injection Mode and Misfire Count Cylinder #1 to Misfire Count Cylinder #6.

Powertrain > Engine > Active Test

Active Test Display
Prohibit the Catalyst OT Misfire Prevent Fuel Cut

Data List Display
Injection Mode
Misfire Count Cylinder #1
Misfire Count Cylinder #2
Misfire Count Cylinder #3
Misfire Count Cylinder #4
Misfire Count Cylinder #5
Misfire Count Cylinder #6

(f) Read each value for Misfire Count Cylinder #1 to Misfire Count Cylinder #6 and Injection Mode displayed on the Techstream while performing the Active Test.

Injection Mode	Misfire Count	Proceed to
Port	1 or 2 cylinders have misfire counts	A
	3 cylinders or more have misfire counts	A
	There are no misfire counts	B

GO TO STEP 8

GO TO STEP 11

7.	CHECK MISFIRE COUNT OF PORT INJECTION

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(d) Start the engine and warm it up.

(e) Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Mode / Port / Data List / Injection Mode and Misfire Count Cylinder #1 to Misfire Count Cylinder #6.

Powertrain > Engine > Active Test

Active Test Display
Control the Injection Mode

Data List Display
Injection Mode
Misfire Count Cylinder #1
Misfire Count Cylinder #2
Misfire Count Cylinder #3
Misfire Count Cylinder #4
Misfire Count Cylinder #5
Misfire Count Cylinder #6

HINT:

When using the "Control the Injection Mode" Active Test to check the condition of the engine, switch from "Port" to "Direct".
Do not switch from "Direct" to "Port". When performing the inspection more than once, after the Active Test ends, lightly race the engine, and then perform the inspection from "Port" again.
If the display does not switch from "Port" even after lighting racing the engine, idle the engine for approximately 1 minute, and then lightly race the engine.

(f) Read each value for Misfire Count Cylinder #1 to Misfire Count Cylinder #6 and Injection Mode displayed on the Techstream. If no misfire counts occur in any cylinders, perform procedure [A] and [B] and then check the misfire counts again.

(1) Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read Value Using Techstream (Misfire RPM and Misfire Load)" procedures above [A].

(2) Read the Injection Mode and Misfire Count Cylinder #1 to Misfire Count Cylinder #6 or DTCs displayed on the Techstream [B].

Injection Mode	Misfire Count	Proceed to
Port	1 or 2 cylinders have misfire counts	A
	3 cylinders or more have misfire counts	A
	There are no misfire counts	B

GO TO STEP 11

8.	CHECK MISFIRE COUNT OF DIRECT INJECTION

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(d) Start the engine and warm it up.

(e) Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Mode / Direct / Data List / Injection Mode and Misfire Count Cylinder #1 to Misfire Count Cylinder #6.

Powertrain > Engine > Active Test

Active Test Display
Control the Injection Mode

Data List Display
Injection Mode
Misfire Count Cylinder #1
Misfire Count Cylinder #2
Misfire Count Cylinder #3
Misfire Count Cylinder #4
Misfire Count Cylinder #5
Misfire Count Cylinder #6

HINT:

When using the "Control the Injection Mode" Active Test to check the condition of the engine, switch from "Port" to "Direct".
Do not switch from "Direct" to "Port". When performing the inspection more than once, after the Active Test ends, lightly race the engine, and then perform the inspection from "Port" again.
If the display does not switch from "Port" even after lighting racing the engine, idle the engine for approximately 1 minute, and then lightly race the engine.

(1) Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read Value Using Techstream (Misfire RPM and Misfire Load)" procedures above [A].

(2) Read the Injection Mode and Misfire Count Cylinder #1 to Misfire Count Cylinder #6 or DTCs displayed on the Techstream [B].

Misfire Count		Proceed to
Port (Result of step 6 or 7)	Direct	Proceed to
1 or 2 cylinders have misfire counts	1 or 2 cylinders have misfire counts	A
3 cylinders or more have misfire counts	3 cylinders or more have misfire counts	B
1 or 2 cylinders have misfire counts	There are no misfire counts	C
3 cylinders or more have misfire counts	There are no misfire counts	D

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly (for port injection).

Click here

GO TO STEP 13

GO TO STEP 16

REPLACE FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION (MISFIRING CYLINDER))

9.	CHECK FUEL PRESSURE (FOR LOW PRESSURE SIDE)

(a) Check the fuel pressure (for low pressure side).

Click here

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly (for port injection).

Click here

REPLACE FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION (MISFIRING CYLINDER))

10.	CHECK FURL PUMP OPERATION (FOR LOW PRESSURE SIDE)

(a) Check the fuel pump operation (for low pressure side).

Click here

CHECK AND REPLACE FUEL SYSTEM

GO TO FUEL PUMP CONTROL CIRCUIT

11.	CHECK MISFIRE COUNT OF DIRECT INJECTION

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(d) Start the engine and warm it up.

(e) Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Mode / Direct / Data List / Injection Mode and Misfire Count Cylinder #1 to Misfire Count Cylinder #6.

Powertrain > Engine > Active Test

Active Test Display
Control the Injection Mode

Data List Display
Injection Mode
Misfire Count Cylinder #1
Misfire Count Cylinder #2
Misfire Count Cylinder #3
Misfire Count Cylinder #4
Misfire Count Cylinder #5
Misfire Count Cylinder #6

HINT:

When using the "Control the Injection Mode" Active Test to check the condition of the engine, switch from "Port" to "Direct".
Do not switch from "Direct" to "Port". When performing the inspection more than once, after the Active Test ends, lightly race the engine, and then perform the inspection from "Port" again.
If the display does not switch from "Port" even after lighting racing the engine, idle the engine for approximately 1 minute, and then lightly race the engine.

(1) Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read Value Using Techstream (Misfire RPM and Misfire Load)" procedures above [A].

(2) Read the Injection Mode and Misfire Count Cylinder #1 to Misfire Count Cylinder #6 or DTCs displayed on the Techstream [B].

Misfire Count		Proceed to
Port (Result of step 6 or 7)	Direct	Proceed to
There are no misfire counts	There are misfire counts	A
There are no misfire counts	There are no misfire counts	B

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly (for direct injection).

Click here

REPLACE FUEL INJECTOR ASSEMBLY (FOR DIRECT INJECTION)

12.	CHECK MISFIRE COUNT

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG) and turn the Techstream on.

Powertrain > Engine > Clear DTCs

(d) Start the engine and warm it up.

(e) Enter the following menus: Powertrain / Engine / Data List / Injection Mode, Misfire Count Cylinder #1 to Misfire Count Cylinder #6, Misfire RPM and Misfire Load.

Powertrain > Engine > Data List

Tester Display
Injection Mode
Misfire Count Cylinder #1
Misfire Count Cylinder #2
Misfire Count Cylinder #3
Misfire Count Cylinder #4
Misfire Count Cylinder #5
Misfire Count Cylinder #6
Misfire RPM
Misfire Load

(f) Drive the vehicle with Misfire RPM and Misfire Load.

(g) Monitor all of the misfire count values or DTCs and Injection Mode displayed on the Techstream.

Misfire Count	Injection Mode	Proceed to
There are no misfire counts	-	A
1 or 2 cylinders have misfire counts	Port or Either	B
3 cylinders or more have misfire counts	Port or Either	C
There are misfire counts	Direct	D

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly (for direct injection).

Click here

CHECK FOR INTERMITTENT PROBLEMS

GO TO STEP 16

REPLACE FUEL INJECTOR ASSEMBLY (FOR DIRECT INJECTION)

13.	INSPECT SPARK PLUG

(a) Inspect the spark plug of the misfiring cylinder.

Click here

HINT:

Perform "Inspection After Repair" after replacing the spark plug.

Click here

REPLACE SPARK PLUG

14.	CHECK FOR SPARK (SPARK TEST)

(a) Perform a spark test.

Click here

HINT:

If the result of the spark test is normal, proceed to the next step.
Perform "Inspection After Repair" after replacing the spark plug or ignition coil assembly.
Click here

15.	CHECK CYLINDER COMPRESSION PRESSURE

(a) Measure the cylinder compression pressure of the misfiring cylinder.

Click here

HINT:

Perform "Inspection After Repair" after repairing or replacing the engine assembly.

Click here

REPLACE ECM

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

16.	CHECK INTAKE SYSTEM

(a) Check the intake system for vacuum leaks.

Click here

OK:

No leaks from the intake system.

HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click here

REPAIR OR REPLACE INTAKE SYSTEM

17.	READ VALUE USING TECHSTREAM (COOLANT TEMPERATURE)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(d) Enter the following menus: Powertrain / Engine / Data List / Coolant Temperature.

Powertrain > Engine > Data List

Tester Display
Coolant Temperature

(e) Read the Data List twice, when the engine is both cold and warmed up.

Standard:

Techstream Display	Condition	Specified Condition
Coolant Temperature	Cold engine	Same as ambient air temperature
Coolant Temperature	Warm engine	Between 75 and 100°C (167 and 212°F)

HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click here

REPLACE ENGINE COOLANT TEMPERATURE SENSOR

18.	READ VALUE USING TECHSTREAM (MASS AIR FLOW SENSOR)

(a) Connect the Techstream to the DLC3.

(b) Start the engine.

(d) Enter the following menus: Powertrain / Engine / Data List / Engine Speed, Mass Air Flow Sensor and Coolant Temperature.

Powertrain > Engine > Data List

Tester Display
Engine Speed
Mass Air Flow Sensor
Coolant Temperature

(e) Allow the engine to idle until Coolant Temperature reaches 75°C (167°F) or higher.

(f) Read Mass Air Flow Sensor while maintaining an engine speed of 3000 rpm.

Standard:

Techstream Display

Condition

Specified Condition

Mass Air Flow Sensor

Engine warmed up

Shift lever position: P

A/C: Off

Engine Speed: 3000 rpm

Between 10.6 gm/sec and 15.8 gm/sec

GO TO STEP 22

19.	CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

(a) Remove the cylinder head cover sub-assembly and cylinder head cover sub-assembly LH.

*a	Timing Mark	*b	TDC Timing Mark
*c	Groove	-	-

(b) Turn the crankshaft pulley and align its groove with the TDC timing mark of the timing chain cover.

(c) Check that the timing marks of the camshaft timing gear assemblies and camshaft timing exhaust gear assemblies are aligned with the timing marks of the bearing cap as shown in the illustration.

HINT:

If the timing marks are not as shown, turn the crankshaft one revolution clockwise.

OK:

Timing marks on camshaft timing gear assemblies and camshaft timing exhaust gear assemblies are aligned as shown in the illustration.

HINT:

If the result is not as specified, check for mechanical malfunctions that may have affected the valve timing, such as a jumped tooth or stretching of the timing chain.

GO TO STEP 22

20.	CHECK ENGINE MECHANICAL SYSTEM

(a) Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

21.	CONFIRM WHETHER DTC OUTPUT RECURS (MISFIRE DTCS)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(d) Clear the DTCs.

Powertrain > Engine > Clear DTCs

(e) Turn the engine switch off and wait for at least 30 seconds.

(f) Turn the engine switch on (IG).

(g) Turn the Techstream on.

(h) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

(i) Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility

Tester Display
All Readiness

(j) Input the DTC: P030000, P030027, P030085, P030100, P030200, P030300, P030400, P030500 or P030600.

(k) Check the DTC judgment result.

Result

Proceed to

NORMAL

(DTCs are not output)

ABNORMAL

(DTC P030000, P030027, P030085, P030100, P030200, P030300, P030400, P030500 and/or P030600 are output)

CHECK FOR INTERMITTENT PROBLEMS

GO TO STEP 22

22.	CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)

(a) Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter sub-assembly and ECM.

Click here

HINT:

Repair any problems.

23.	CHECK WHETHER DTC OUTPUT RECURS (MISFIRE DTCS)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(d) Clear the DTCs.

Powertrain > Engine > Clear DTCs

(e) Turn the engine switch off and wait for at least 30 seconds.

(f) Turn the engine switch on (IG).

(g) Turn the Techstream on.

(h) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

(i) Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility

Tester Display
All Readiness

(j) Input the DTC: P030000, P030027, P030085, P030100, P030200, P030300, P030400, P030500 or P030600.

(k) Check the DTC judgment result.

Result

Proceed to

NORMAL

(DTCs are not output)

ABNORMAL

(DTC P030000, P030027, P030085, P030100, P030200, P030300, P030400, P030500 and/or P030600 are output)

END

24.	CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

(a) Disconnect the mass air flow meter sub-assembly connector.

(b) Disconnect the ECM connector.

Standard Resistance:

Tester Connection	Condition	Specified Condition
D9-3 (5V) - D2-90 (VC)	Always	Below 1 Ω
D9-1 (FG) - D2-116 (VG)	Always	Below 1 Ω
D9-2 (E2G) - D2-115 (E2G)	Always	Below 1 Ω
D9-3 (5V) or D2-90 (VC) - Body ground and other terminals	Always	10 kΩ or higher
D9-1 (FG) or D2-116 (VG) - Body ground and other terminals	Always	10 kΩ or higher
D9-2 (E2G) or D2-115 (E2G) - Body ground and other terminals	Always	10 kΩ or higher

REPAIR OR REPLACE HARNESS OR CONNECTOR

25.	REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

(a) Replace the mass air flow meter sub-assembly.

Click here

HINT:

If the results of the inspections performed in step 17 indicated no problem, proceed to the next step without replacing the mass air flow meter sub-assembly.
Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.
Click here

26.	CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(d) Clear the DTCs.

Powertrain > Engine > Clear DTCs

(e) Turn the engine switch off and wait for at least 30 seconds.

(f) Turn the engine switch on (IG).

(g) Turn the Techstream on.

(h) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

(i) Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility

Tester Display
All Readiness

(j) Input the DTC: P030000, P030027, P030085, P030100, P030200, P030300, P030400, P030500 or P030600.

(k) Check the DTC judgment result.

Result

Proceed to

NORMAL

(DTCs are not output)

ABNORMAL

(DTC P030000, P030027, P030085, P030100, P030200, P030300, P030400, P030500 and/or P030600 are output)

END

REPLACE ECM

Cylinder 1 Injector "A" Circuit Open (P020113-P020613,P062D13)

DESCRIPTION The D-4S system has two fuel injection systems. One is an in-cylinder direct injection system that directly injects pressurized fuel into the combustion chamber. The other is an intake por ...

Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Ground (P032511,P033011)

DESCRIPTION A flat-type knock control sensor (non-resonant type) has a structure that can detect vibrations between approximately 5 kHz and 15 kHz. The knock control sensor is fitted onto the engine b ...

Other materials:

Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Camshaft Position Sensor: Components
COMPONENTS ILLUSTRATION *1 VVT SENSOR (for Intake Side of Bank 1) *2 VVT SENSOR (for Exhaust Side of Bank 1) *3 VVT SENSOR (for Intake Side of Bank 2) *4 VVT SENSOR (for Exhaust Side of Bank 2) N*m (kgf*cm, ft.*lbf): Specified torque Adhesive 1324 ★ Precoated ...

Lexus RX (RX 350L, RX450h) 2016-2024 Owners Manual > Lexus RX (RX 350L, RX450h) 2016-2024 Owners Manual: For owners
Reporting safety defects for U.S. owners If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying the Lexus Division of Toyota Mot ...

Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual: Random/Multiple Cylinder Misfire Detected (P030000,P030027,P030085-P030600)

Cylinder 1 Injector "A" Circuit Open (P020113-P020613,P062D13)

Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Ground (P032511,P033011)

Other materials:

Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual