INSTALLATION
CAUTION / NOTICE / HINT
HINT:
PROCEDURE
1. INSTALL REAR DOOR REAR WINDOW FRAME MOULDING
(a) Using an air riveter or hand riveter with a nose piece, install the rear door rear window frame moulding with 3 new rivets.
HINT:
If the mandrel of the rivet does not come off on the first operation of the rivet gun, slide the rivet gun forward on the mandrel and operate it again.
NOTICE:
*a | Riveter |
*b | Mandrel |
*c | Incorrect |
*a | Riveter |
*b | Incorrect |
*a | Riveter |
*b | Incorrect |
2. INSTALL REAR DOOR UPPER WINDOW FRAME MOULDING
(a) Engage the guide of the rear door upper window frame moulding to the door frame.
(b) Using an air riveter or hand riveter with a nose piece, install the rear door upper window frame moulding with 4 new rivets.
HINT:
If the mandrel of the rivet does not come off on the first operation of the rivet gun, slide the rivet gun forward on the mandrel and operate it again.
NOTICE:
*a | Riveter |
*b | Mandrel |
*c | Incorrect |
*a | Riveter |
*b | Incorrect |
*a | Riveter |
*b | Incorrect |
3. INSTALL REAR DOOR WINDOW FRAME MOULDING SUB-ASSEMBLY
HINT:
When installing a new rear door window frame moulding sub-assembly, heat the vehicle body and rear door window frame moulding sub-assembly using a heat light.
Heating Temperature Item | Temperature |
---|---|
Vehicle Body | 40 to 60°C (104 to 140°F) |
Rear Door Window Frame Moulding Sub-assembly | 20 to 30°C (68 to 86°F) |
CAUTION:
*a | Heated Part |
*b | Heat Light |
NOTICE:
Do not heat the vehicle body or rear door window frame moulding sub-assembly excessively.
(a) Clean the vehicle body surface.
(1) Using a heat light, heat the vehicle body surface.
(2) Remove any double-sided tape from the vehicle body.
(3) Wipe off any tape adhesive residue with cleaner.
(b) Install a new rear door window frame moulding sub-assembly.
(1) Using a heat light, heat the vehicle body and rear door window frame moulding sub-assembly.
(2) Remove the release paper from the new rear door window frame moulding sub-assembly.
HINT:
After removing the release paper, keep the exposed adhesive free from foreign matter.
(3) Engage the clip and guide and attach the double-sided tape and caulking sponge to install the rear door window frame moulding sub-assembly. HINT: Press the rear door window frame moulding sub-assembly firmly to install it. |
|
4. CONNECT REAR DOOR WEATHERSTRIP
(a) Engage the 5 clips and connect the rear door weatherstrip.
5. INSTALL REAR DOOR BELT MOULDING ASSEMBLY
Click here
Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Dynamic Radar Cruise Control System: Invalid Data Received from ECM/PCM "A" Invalid Serial Data Received (U040181)
DESCRIPTION If the ECM cannot recognize the forward recognition camera. DTC U040181 is stored. DTC No. Detection Item DTC Detection Condition Trouble Area MIL DTC Output from U040181 Invalid Data Received from ECM/PCM "A" Invalid Serial Data Received Approximately 17 seconds or ...
Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Pre-collision System: Lost Communication with ECM/PCM "A" Missing Message (U010087,U012587,U012687,U012987)
DESCRIPTION When a malfunction is detected between various ECUs and sensors, these DTCs are stored. DTC No. Detection Item DTC Detection Condition Trouble Area U010087 Lost Communication with ECM/PCM "A" Missing Message While the vehicle is being driven at 5 km/h (4 mph) or more, a ...