Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual: Data List / Active Test

DATA LIST / ACTIVE TEST

DATA LIST

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus:

(1) for Combination Meter: Body Electrical / Combination Meter / Data List.

(2) for Brake/EPB: Chassis / Brake/EPB / Data List.

(3) for Engine: Powertrain / Engine / Data List.

(e) Read the Data List according to the display on the Techstream.

(1) Combination Meter

Body Electrical > Combination Meter > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

ODO/TRIP Change SW

ODO/TRIP switch

OFF or ON

OFF: Switch released

ON: Switch pushed

-

Vehicle Speed Meter

Vehicle speed

Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)

Almost the same as actual vehicle speed

-

Engine Rpm

Engine speed

Min.: 0 rpm, Max.: 12750 rpm

Almost the same as actual tachometer

-

Coolant Temperature

Engine coolant temperature

Min.: 0°C (32°F), Max.: 127.5°C (261.5°F)

75 to 100°C (167 to 212°F): After warming up engine

-

Washer Switch

Washer fluid level warning switch

OFF or ON

OFF: Washer fluid level not low

ON: Washer fluid level low

-

Oil Level SW

Engine oil level sensor

OFF or ON

OFF: Engine oil level not low

ON: Engine oil level low

-

Light Control Up Switch

Light control rheostat up switch

OFF or ON

OFF: Switch released

ON: Switch pushed

-

Light Control Down Switch

Light control rheostat down switch

OFF or ON

OFF: Switch released

ON: Switch pushed

-

+B Voltage Value

Battery voltage

Min.: 0 V, Max.: 25.5 V

11 to 14 V

-

Fuel Input

Fuel input

Min.: 0 L, Max.: 127.5 L

Fuel receiver gauge indicates F: 64.8 L

Fuel receiver gauge indicates 3/4: 54.0 L

Fuel receiver gauge indicates 1/2: 36.0 L

Fuel receiver gauge indicates 1/4: 18.0 L

Fuel receiver gauge indicates E: 7.2 L

Unit: Liter

Ambient Temperature

Outside temperature

Min.: -40°C (-40°F), Max.: 87.5°C (189.5°F)

Almost the same as actual outside temperature

The temperature displayed on the multi-information display is -40 to 50°C (-40 to 122°F)

Multi Switch (Up)

Steering pad switch (Up)

OFF or ON

OFF: Switch released

ON: Switch pushed

-

Multi Switch (Down)

Steering pad switch (Down)

OFF or ON

OFF: Switch released

ON: Switch pushed

-

Multi Switch (Menu)

Steering pad switch (Menu)

OFF or ON

OFF: Switch released

ON: Switch pushed

-

Multi Switch (Enter)

Steering pad switch (Enter)

OFF or ON

OFF: Switch released

ON: Switch pushed

-

Multi Switch (Right)

Steering pad switch (Right)

OFF or ON

OFF: Switch released

ON: Switch pushed

-

Multi Switch (Left)

Steering pad switch (Left)

OFF or ON

OFF: Switch released

ON: Switch pushed

-

2nd-Row Seatbelt Buckle (R)

Rear seat belt buckle switch RH

OFF or ON

OFF: Rear seat belt RH fastened

ON: Rear seat belt RH unfastened

-

2nd-Row Seatbelt Buckle (L)

Rear seat belt buckle switch LH

OFF or ON

OFF: Rear seat belt LH fastened

ON: Rear seat belt LH unfastened

-

2nd-Row Seatbelt Buckle (C)

Rear seat belt buckle switch center

OFF or ON

OFF: Rear seat belt center fastened

ON: Rear seat belt center unfastened

*1

3rd-Row Seatbelt Buckle (R)

Rear No. 2 seat belt buckle switch RH

OFF or ON

OFF: Rear No. 2 seat belt RH fastened

ON: Rear No. 2 seat belt RH unfastened

*2

3rd-Row Seatbelt Buckle (L)

Rear No. 2 seat belt buckle switch LH

OFF or ON

OFF: Rear No. 2 seat belt LH fastened

ON: Rear No. 2 seat belt LH unfastened

*2

Oil Pressure Switch

Engine oil pressure switch

OFF or ON

OFF: Engine started

ON: Engine not started

-

Turn Signal Switch (Right)

RH turn signal switch

OFF or ON

OFF: RH turn signal switch off

ON: RH turn signal switch on

-

Turn Signal Switch (Left)

LH turn signal switch

OFF or ON

OFF: LH turn signal switch off

ON: LH turn signal switch on

-

Hazard Flasher Switch

Hazard warning signal switch

OFF or ON

OFF: Hazard warning signal switch off

ON: Hazard warning signal switch on

-

Passenger Occupant Detection Switch

Occupant detection sensor

OFF or ON

OFF: Front passenger seat not occupied

ON: Front passenger seat occupied

Not applicable to this vehicle

Turn Switch Signal (Full Turn)

Turn signal switch signal

OFF or ON

OFF: LH and RH turn signal switch off

ON: LH or RH turn signal switch on

-

Multi Switch (Back)

Steering pad switch (Back)

OFF or ON

OFF: Switch released

ON: Switch pushed

-

Brake Fluid Amount

Brake fluid level

OK or Low

OK: Brake fluid level normal

NG: Brake fluid level abnormal

-

Brake Negative Pressure

Brake vacuum pressure

OK or NG

OK: Brake vacuum pressure normal

NG: Brake vacuum pressure abnormal

-

Driver Side Seatbelt Warning Buzzer

Setting of the driver seat belt warning buzzer

OFF or ON

OFF: Seat belt warning buzzer does not sound at vehicle speed of 20 km/h (12 mph) or more when driver seat belt unfastened

ON: Seat belt warning buzzer sounds at vehicle speed of 20 km/h (12 mph) or more when driver seat belt unfastened

Displays customize setting of Driver Side Seat Belt Warning Buzzer

P-Seatbelt Warning Buzzer

Setting of the front passenger seat belt warning buzzer

OFF or ON

OFF: Seat belt warning buzzer does not sound at vehicle speed of 20 km/h (12 mph) or more when front passenger seat belt unfastened

ON: Seat belt warning buzzer sounds at vehicle speed of 20 km/h (12 mph) or more when front passenger seat belt unfastened

Displays customize setting of Front Passenger Side Seat Belt Warning Buzzer

Rear Seatbelt Warning Buzzer

Setting of the rear seat belt warning buzzer

OFF or ON

OFF: Seat belt warning buzzer does not sound at vehicle speed of 20 km/h (12 mph) or more when rear seat belt unfastened

ON: Seat belt warning buzzer sounds at vehicle speed of 20 km/h (12 mph) or more when rear seat belt unfastened

Displays customize setting of Rear Seat Belt Warning Buzzer

ODO Display Time After IG OFF Setting

Setting of the ODO display time after the engine switch is turned off

30s, 60s, 600s or OFF

Displays customize setting of ODO Display Time After the Engine Switch is Turned Off

-

Lane Change Flashing Times Setting

Setting of the lane change flashing times

OFF, 3, 4, 5, 6 or 7

Displays customize setting of Lane Change Flashing Times Setting

-

Flasher Sound Volume Adjustment

Setting of the flasher sound volume adjustment

Small, Medium or Large

Displays customize setting of Flasher Sound Volume Adjustment

-

TPMS System

Existence of function

With or Without

With: w/ Tire Pressure Warning System

Without: w/o Tire Pressure Warning System

-

LDA System

Existence of function

With or Without

With: w/ Lane Control System

Without: w/o Lane Control System

-

PCS System

Existence of function

With or Without

With: w/ Pre-collision System

Without: w/o Pre-collision System

-

AHS System

Existence of function

With or Without

With: w/ Adaptive High Beam System

Without: w/o Adaptive High Beam System

-

ICS System

Existence of function

With or Without

With: w/ Intelligent Clearance Sonar System

Without: w/o Intelligent Clearance Sonar System

-

Radar Cruise System

Existence of function

With or Without

With: w/ Dynamic Radar Cruise Control System

Without: w/o Dynamic Radar Cruise Control System

-

Intuitive P/A System

Existence of function

With or Without

With: w/ Intuitive Parking Assist System

Without: w/o Intuitive Parking Assist System

-

Back Door System

Existence of function

With or Without

With: w/ Power Back Door System

Without: w/o Power Back Door System

-

Road Sign Assist System

Existence of function

With or Without

With: w/ Road Sign Assist System

Without: w/o Road Sign Assist System

-

Number of Trouble Code

The number of the DTC currently stored

Min.: 0, Max.: 255

Number of stored DTCs displayed

-

  • *1: w/ Rear No. 2 Seat (for 60/40 Split Type Rear No. 1 Seat) or without Rear No. 2 Seat

    *2: w/ Rear No. 2 Seat

(2) Brake/EPB

Chassis > Brake/EPB > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Vehicle Speed

Maximum wheel speed sensor reading

Min.: 0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph)

Vehicle stopped: 0 km/h (0 mph)

When driving at constant speed: No large fluctuations

(3) Engine

Powertrain > Engine > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Engine Speed

Engine speed

Min.: 0 rpm, Max.: 16383 rpm

650 to 750 rpm: Idling (shift lever in N, engine warmed up and A/C off)

When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.

Coolant Temperature

Engine coolant temperature

Min.: -40°C (-40°F), Max.: 140°C (284°F)

75 to 100°C (167 to 212°F): After warming up

This is the engine coolant temperature.

HINT:

  • After warming up the engine, the engine coolant temperature will be 75 to 100°C (167 to 212°F).
  • After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature will be approximately equal.
  • If the value is -40°C (-40°F), or higher than 135°C (275°F), the sensor circuit is open or shorted.
  • Check if the engine overheats if the value indicated is higher than 135°C (275°F).

ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Combination Meter / Active Test.

(e) Perform the Active Test according the display on the Techstream.

Body Electrical > Combination Meter > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Speed Meter Operation

Speedometer*1

  • OFF, 0, 40, 80, 120 or 160 mph*5
  • OFF, 0, 40, 80, 120, 160, 200 or 240 km/h*6

There is a deviation in the values displayed on the speedometer (Control range → Speedometer display)

for Optitron Meter Type (mph)*5:
  • 40 → 39.6 to 42.4
  • 80 → 80.5 to 83.7
  • 120 → 121.5 to 124.7
for Optitron Meter Type (km/h)*6:
  • 40 → 38.8 to 43.3
  • 80 → 79.6 to 84.6
  • 120 → 120.6 to 125.6
  • 160 → 161.7 to 166.7
  • 200 → 202.7 to 207.7
  • 240 → 243.7 to 248.7

TachoMeter Operation

Tachometer

OFF, 0, 1000, 2000, 3000, 4000, 5000, 6000 or 7000

*1

Fuel Meter Operation

Fuel receiver gauge

OFF, Sender E, Empty, Warning, 1/4, 1/2, 3/4, Full or Sender F

-

A/T Indicator Operation 1

Shift indicator

OFF, L, 2, 3, 4, D, N, R or P

-

A/T Indicator Operation 2

Shift indicator

OFF, 8, 5, 6, 7, S or M

-

A/T Indicator Operation 3

Shift indicator

OFF or D

-

Indicat. Lamp Airbag

SRS warning light

OFF or ON

-

Driver Side Seat Belt

Driver or front passenger seat belt warning light

OFF or ON

-

Indicat. Lamp ABS

ABS warning light

OFF or ON

-

Indicat. Lamp Charge

Charge warning light

OFF or ON

*2

Indicat. Lamp Slip

Slip indicator light

OFF or ON

-

Indicat. Lamp Beam

High beam indicator light

OFF or ON

-

Indicat. Lamp Head

Head indicator light

OFF or ON

*3

Indicat. Lamp Tail

Tail indicator light

OFF or ON

*4

Indicat. Lamp Fr FOG

Front fog indicator light

OFF or ON

-

Indicat. Pre-Collision

PCS warning light

OFF or ON

-

Indicat. Lamp Fuel

Fuel level warning light

OFF or ON

-

Indicat. Tire Pressure Warning System

Tire pressure warning light

OFF or ON

-

Indicat. Lamp ECB

Brake warning light / yellow (minor malfunction)

OFF or ON

-

Indicat. ECONO

Eco driving indicator light

OFF or ON

-

Indicat. Lamp Brake

Brake warning light / red (malfunction)

OFF or ON

-

Indicat. EPS

EPS warning light (red)

OFF or ON

-

Master Warning

Master warning light

OFF or ON

-

Indicat. Brake Hold

Brake hold indicator light

OFF or ON

-

Indicat. Hold

Brake hold warning light

OFF or ON

-

Indicat. Park

Parking brake warning light

OFF or ON

-

Indicat. VSC OFF

VSC OFF indicator light

OFF or ON

-

Rear Seat Belt

Rear seat belt warning light

OFF or ON

-

Indicat. 4WD Lock

AWD lock indicator light

OFF or ON

*9

Automatic High Beam Indicator

Automatic high beam indicator light

OFF or ON

-

PPS Indicator

EPS warning light (yellow)

OFF or ON

-

Turn Signal (Left) Indicator

LH turn indicator light

OFF or ON

-

Turn Signal (Right) Indicator

RH turn indicator light

OFF or ON

-

Check Engine Indicator

MIL (Check engine warning light)

OFF or ON

-

BSM Control Indicator

BSM indicator light

OFF or ON

*7

ICS OFF Indicator

ICS OFF indicator light

OFF or ON

*8

INTUITIVE P/A LCD OFF Indicator

Clearance sonar OFF indicator light

OFF or ON

*8

RCTA OFF Indicator

RCTA OFF indicator light

OFF or ON

-

Water Temperature Meter Operation

Engine coolant temperature receiver gauge

OFF, LOW, NORMAL or HIGH

-

Meter Display 1

Multi-information display

OFF or All

-

  • *1: for Optitron Meter Type
  • *2: for TFT Meter Type
  • *3: w/ Head Indicator Light
  • *4: w/ Tail Indicator Light
  • *5: for Speedometer with Imperial Units Main Scale
  • *6: for Speedometer with Metric Units Main Scale
  • *7: w/ Blind Spot Monitor System
  • *8: w/ Intelligent Clearance Sonar System
  • *9: for AWD

HINT:

Active Test cannot be performed on the speedometer and tachometer for TFT meter type.

    Freeze Frame Data
    FREEZE FRAME DATA FREEZE FRAME DATA (a) Whenever a meter DTC is detected, the combination meter assembly stores the current vehicle state as freeze frame data. CHECK FREEZE FRAME DATA (a) Connect the ...

    Diagnostic Trouble Code Chart
    DIAGNOSTIC TROUBLE CODE CHART Meter / Gauge System DTC No. Detection Item Memory Note Link B1321 Lost Communication with EMV DTC stored - B1326 Lost Communication with ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Front Seatback Heater: Components
    COMPONENTS ILLUSTRATION *A for Standard Seat Type *B for Sports Seat Type *1 FRONT SEAT CUSHION SHIELD *2 FRONT SEAT INNER CUSHION SHIELD *3 INNER NO. 1 FRONT SEAT CUSHION SHIELD - - ILLUSTRATION *1 SEPARATE TYPE FRONT SEATBACK ASSEMBLY *2 SEPARATE TYPE FRO ...

    Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Transfer System: Precaution
    PRECAUTION PRECAUTION (a) Prior to starting any work, clean the transfer assembly to prevent sand or mud deposits from entering the assembly. (b) When removing any light alloy components such as the transfer cover, do not pry on the component with a screwdriver or similar tool. Tap the component loo ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2024 Copyright www.lexusrx.net
    0.0108