COMPONENTS
ILLUSTRATION
*1 | REAR DOOR SCUFF PLATE LH | *2 | REAR NO. 1 SEAT ASSEMBLY LH |
*3 | REAR SEAT HEADREST ASSEMBLY | *4 | REAR SEAT INNER TRACK BRACKET COVER LH |
*5 | REAR SEAT OUTER TRACK BRACKET COVER LH | *6 | REAR SEAT OUTER TRACK BRACKET COVER LH |
*7 | SEAT INNER TRACK BRACKET COVER LH | - | - |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | - | - |
ILLUSTRATION
*A | w/ Seat Heater System | - | - |
*1 | NO. 1 RECLINING ADJUSTER RELEASE HANDLE LH | *2 | REAR NO. 1 SEAT RECLINING ADJUSTER INSIDE COVER |
*3 | REAR SEAT COVER CAP LH | *4 | REAR SEAT CUSHION EDGE PROTECTOR |
*5 | REAR SEAT INNER BELT ASSEMBLY LH | *6 | REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH |
*7 | SEAT ADJUSTER COVER CAP | *8 | SEAT COVER WIRE |
*9 | SEAT HEATER ASSEMBLY | *10 | SEAT HEATER CONTROL SUB-ASSEMBLY LH |
*11 | SEPARATE TYPE REAR SEAT CUSHION COVER | *12 | SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD |
*13 | REAR SEAT CUSHION PAD LH | *14 | HOG RING |
*15 | TAG PIN | - | - |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
ILLUSTRATION
*A | w/ Seat Heater System | - | - |
*1 | NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY LH | *2 | REAR SEAT AIRBAG ASSEMBLY LH |
*3 | REAR SEAT UPPER RECLINING COVER LH | *4 | REAR SEATBACK BOARD CARPET ASSEMBLY LH |
*5 | REAR SEATBACK COVER LH | *6 | REAR SEATBACK EDGE PROTECTOR |
*7 | RECLINING REMOTE CONTROL BEZEL LH | *8 | RECLINING REMOTE CONTROL LEVER SUB-ASSEMBLY LH |
*9 | SEAT COVER WIRE | *10 | SEAT HEATER ASSEMBLY |
*11 | SEPARATE TYPE REAR SEATBACK COVER | *12 | SEPARATE TYPE REAR SEATBACK COVER WITH PAD |
*13 | SEPARATE TYPE REAR SEATBACK PAD | *14 | REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY |
*15 | HOG RING | *16 | TAG PIN |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
ILLUSTRATION
*1 | NO. 1 RECLINING LINK COVER LH | *2 | NO. 2 RECLINING LINK COVER LH |
*3 | REAR NO. 1 SEAT RECLINING ADJUSTER INSIDE COVER | *4 | REAR NO. 1 SEAT RECLINING ADJUSTER INSIDE COVER |
*5 | REAR NO. 1 SEAT RECLINING ADJUSTER INSIDE COVER | *6 | REAR NO. 1 SEAT RECLINING ADJUSTER INSIDE COVER |
*7 | REAR NO. 1 SEAT RECLINING COVER LH | *8 | REAR NO. 1 SEAT TRACK CONTROL CABLE ASSEMBLY LH |
*9 | REAR SEAT INNER RECLINING COVER LH | *10 | REAR SEAT RECLINING CONTROL CABLE |
*11 | REAR SEAT RECLINING SEAT COVER LH | *12 | REAR SEAT RECLINING SEAT COVER LH |
*13 | REAR SEAT WIRE LH | *14 | RECLINING ADJUSTING CABLE ASSEMBLY |
ILLUSTRATION
*1 | REAR SEATBACK FRAME SUB-ASSEMBLY LH | *2 | RECLINING CONTROL LINK SUB-ASSEMBLY LH |
*3 | NO. 1 SEAT CUSHION FRAME SUB-ASSEMBLY LH | - | - |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | N*m (kgf*cm, ft.*lbf): Specified torque |
Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Rear Seat Outer Belt Assembly: Installation
INSTALLATION CAUTION / NOTICE / HINT HINT:
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
PROCEDURE 1. INSTALL OUTER BELT ANCHOR BRACKET SUB-ASSEMBLY (for TMC Made) (a) Install the outer belt anchor bracket sub-assembly with the 2 bolts. Torqu ...
Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Exhaust Pipe: Removal
REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front exhaust pipe assembly, front No. 3 exhaust pipe sub-assembly, center exhaust pipe assembly (TWC: R ...