Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual: Dcm Operation History

DCM OPERATION HISTORY

DCM OPERATION HISTORY

HINT:

  • This function shows the telematics network status when the DCM (telematics transceiver) was operated. Use this when no DTC is present but this telematics system was unable to connect to the call center. This symptom may occur if cell phone signal strength is very weak.
  • This function is used to display operation history information and the time at which it was stored in the DCM (telematics transceiver).

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Choose "Telematics" from the System Selection Menu, and then click "Utility".

(e) Click "DCM Operation History" on the Utility Selection Menu.

Body Electrical > Telematics > Utility

Tester Display

DCM Operation History

(f) Choose "Items" on the DCM Operation History Menu.

HINT:

  • When "Operation Code" is recorded, DCM Operation History is displayed on the Techstream.
  • The displayed "Function" differs depending on the selected "Items".

(g) Refer to the following chart and check the system operation status displayed on the Techstream. (The following chart is an example of the system operation status.)

System Operation Status Example

Occurrence time (*1)

Operation Code (*2)

Function (*3)

Content (*4)

Roaming (*5)

Voice Call (*6)

Service Area (*7)

Electric Level (*8)

2017/12/31 12:40:50

0101

GNSS (Satellite)

Unreceived GNSS (Satellite) signal

ON

With

Out of Service

Level 0

Tester Display Description
 

Tester Display

Description

Range

*1

Occurrence time

Indicates date of the DCM (telematics transceiver) operation.

-

*2

Operation Code

Indicates the Operation Code.

-

*3

Function

Items

Indicates the function name.

-

Common

  • GNSS (Satellite)
  • Collision Detection
  • Network Power Supply Control
  • SMS
  • Telematics PF
  • Failure Due to Conflict
  • Activate Function

Emergency Call

  • Emergency Call
  • Automatic Maintenance
  • Manual Maintenance

*4

Content

Indicates the content.

-

*5

Roaming

Indicates whether roaming was used for the communication network.

ON or OFF

*6

Voice Call

Indicates whether there was a voice call.

With or Without

*7

Service Area

Indicates whether the vehicle was in the service area.

Out of Service, Within Range, OFF the Air or Start up (LTE)

*8

Electric Level

Indicates the strength of the cellular signal received by the vehicle.

Level 0, Level 1, Level2, Level3, Level 4, Level 5

    How To Proceed With Troubleshooting
    CAUTION / NOTICE / HINT HINT: Use the following procedure to troubleshoot the safety connect system. *: Use the Techstream. PROCEDURE 1. VEHICLE BROUGHT TO WORKSHOP NEXT ...

    Dcm Activation
    DCM ACTIVATION HINT: If the DCM (telematics transceiver) has been replaced, it is necessary to perform the Register Vehicle Information procedure. DCM ACTIVATION (a) Connect the Techstream to the DLC3 ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Airbag System: Operation Check
    OPERATION CHECK PRECAUTION FOR OPERATION CHECK CAUTION: Use the correct procedure to replace the airbag parts. CHECK SRS WARNING LIGHT (a) Primary check (1) Turn the engine switch on (IG) and check that the SRS warning light turns on. (2) Turn the engine switch off. Wait for at least 2 seconds, an ...

    Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Sfi System: Internal Control Module Accelerator Pedal Position Performance Internal Electronic Failure (P060D49)
    MONITOR DESCRIPTION The ECM monitors the input signals of the No. 1 accelerator pedal position sensor. If the input signals and control signals deviate, this DTC is stored. DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note P060D49 Internal Control Modul ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2024 Copyright www.lexusrx.net
    0.0159