Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual: Installation

Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual / Vehicle Exterior / Window / Glass / Quarter Window Glass (w/o Rear No. 2 Seat) / Installation

INSTALLATION

CAUTION / NOTICE / HINT

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.

PROCEDURE

1. INSTALL QUARTER WINDOW ASSEMBLY

(a) Using a brush, coat the installation surfaces on the vehicle body with primer M.

NOTICE:

  • Do not coat the adhesive with primer M.
  • Do not apply too much primer M.
  • Allow the primer M to dry for 3 minutes or more.
  • Throw away any leftover primer M.

HINT:

If an area other than specified is coated by accident, wipe off the primer M with a clean piece of cloth before it dries.

(b) Using a brush or a sponge, coat the adhesive application area with primer G.

*A

Back Side

-

-

*a

Adhesive Positioning Center

-

-

Primer G

-

-

Standard Dimension:

Area

Dimension

a

15.0 mm (0.591 in.) or more

b

20.0 mm (0.787 in.) or more

c

12.0 mm (0.472 in.) or more

NOTICE:

  • Do not apply too much primer G.
  • Allow the primer G to dry for 3 minutes or more.
  • Throw away any leftover primer G.

HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.

(c) Apply adhesive to a new quarter window assembly.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent

(1) Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard Dimension:

Area

Dimension

a

8.0 to 11.0 mm (0.315 to 0.433 in.)

b

6.0 to 9.0 mm (0.236 to 0.354 in.)

*a

Nozzle

(2) Load the sealer gun with the cartridge.

(3) Apply adhesive to the quarter window assembly as shown in the illustration.

*A

Back Side

-

-

*a

Adhesive Positioning Center

-

-

Adhesive

-

-

Standard Dimension:

Area

Dimension

a

6.0 mm (0.236 in.)

b

6.0 mm (0.236 in.)

c

6.0 mm (0.236 in.)

d

6.0 mm (0.236 in.)

(d) Install the quarter window assembly to the vehicle body.

(1) Using suction cups, engage the 4 clips to install the quarter window assembly.

NOTICE:

  • Check that the clips are engaged to the vehicle body correctly.
  • Check the clearance between the vehicle body and quarter window assembly.

(2) Lightly press the outer surface of the quarter window assembly to ensure that the quarter window assembly is securely fit to the vehicle body.

HINT:

Press the glass with a force of 98 N (10 kgf, 22.0 lbf) or more.

(3) Using a scraper, remove any excess or protruding adhesive.

(4) Hold the quarter window assembly using protective tape until the applied adhesive becomes hard.

HINT:

Follow the instructions supplied by the adhesive manufacturer or in the corresponding instruction manual for the minimum amount of time necessary to wait before driving the vehicle.

2. INSPECT FOR LEAK

(a) After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.

(b) If water leaks into the cabin, allow the water to dry and add adhesive.

(c) Remove the protective tape.

3. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH

Click here

4. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH

Click here

5. INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY (for LH Side)

Click here

6. INSTALL ROPE HOOK ASSEMBLY (for LH Side)

Click here

7. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for LH Side)

Click here

8. INSTALL REAR FLOOR FINISH SIDE PLATE LH

Click here

9. INSTALL REAR SEAT SIDE GARNISH LH

Click here

10. INSTALL UPPER QUARTER TRIM PAD LH

Click here

11. INSTALL REAR SEAT ASSEMBLY LH

Click here

12. INSTALL REAR DOOR SCUFF PLATE LH

Click here

13. INSTALL REAR FLOOR FINISH PLATE

Click here

14. INSTALL DECK SIDE TRIM BOX RH

Click here

15. INSTALL FRONT DECK FLOOR BOX

Click here

16. INSTALL REAR NO. 4 FLOOR BOARD

Click here

17. INSTALL REAR DECK FLOOR BOX

Click here

18. INSTALL REAR NO. 3 FLOOR BOARD

Click here

19. INSTALL DECK BOARD ASSEMBLY

Click here

20. INSTALL TONNEAU COVER ASSEMBLY

Click here

    Components
    COMPONENTS ILLUSTRATION *1 DECK BOARD ASSEMBLY *2 TONNEAU COVER ASSEMBLY ILLUSTRATION *A for TMC Made *B for TMMC Made *1 DECK SIDE TRIM BOX RH *2 FRONT DECK FLOOR BOX ...

    Removal
    REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during quar ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Steering Pad Switch: Installation
    INSTALLATION PROCEDURE 1. INSTALL STEERING PAD SWITCH ASSEMBLY (a) Engage the 2 claws and 2 pins to install the steering pad switch assembly. (b) Install the 2 screws. Torque: 2.4 N·m {24 kgf·cm, 21 in·lbf} (c) Connect the steering pad switch connector to the spiral cable with sensor sub-assembl ...

    Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Power Window Regulator Motor (for Rear Door): Removal
    REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during power window regulator motor removal/installation are shown below. Necessary Procedure After Parts Remov ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2025 Copyright www.lexusrx.net
    0.0189