Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual: AWD Warning Light does not Come ON

DESCRIPTION

Refer to "AWD Warning Light Remains ON".

Click here

WIRING DIAGRAM

Refer to "AWD Warning Light Remains ON".

Click here

CAUTION / NOTICE / HINT

NOTICE:

When the 4WD ECU assembly is replaced with a known good one from another vehicle, it is necessary to perform calibration.

Click here

HINT:

Check the condition of each related circuit connector before troubleshooting.

Click here

PROCEDURE

1.

CHECK CAN COMMUNICATION SYSTEM

(a) Check if CAN communication system DTCs are output.

Click here

Result

Proceed to

CAN communication system DTCs are not output

A

CAN communication system DTCs are output

B

HINT:

If CAN communication DTCs are output, perform troubleshooting for the CAN communication system first.

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

A

2.

INSPECT AWD WARNING

(a) Turn the engine switch off.

(b) Connect the Techstream to the DLC3.

(c) Turn the engine switch on (IG).

(d) Turn the Techstream on.

(e) Enter the following menus: Chassis / Four Wheel Drive / Active Test

(f) According to the display on the Techstream, perform the Active Test.

Chassis > Four Wheel Drive > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

4WD Warning Light

AWD warning (multi-information display)

Warning ON/OFF

Observe the multi-information display.

(g) When performing the 4WD Warning Light Active Test, check 4WD Warning Light in the Data List.

Chassis > Four Wheel Drive > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

4WD Warning Light

AWD warning (multi-information display)

ON or OFF

ON: Warning on

OFF: Warning off

-

Chassis > Four Wheel Drive > Active Test

Active Test Display

4WD Warning Light

Data List Display

4WD Warning Light

Result

Proceed to

Data List item 4WD Warning Light does not change according to the operation of the Active Test

A

Data List item 4WD Warning Light changes according to the operation of the Active Test

B

A

REPLACE 4WD ECU ASSEMBLY

B

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

    AWD Warning Light Remains ON
    DESCRIPTION The 4WD ECU assembly is connected to the combination meter assembly via CAN communication. If the 4WD ECU assembly stores any DTCs which are related to the dynamic torque control AWD syste ...

    AWD Control Switch Circuit
    DESCRIPTION The 4WD ECU assembly changes the control mode in response to the "Lock Mode" signal from the AWD lock switch (combination switch assembly). WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE: ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Roof Drip Side Finish Moulding: Removal
    REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during roof drip side finish moulding removal/installation are shown below. Necessary Procedures After Parts Re ...

    Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Steering Pad Switch: Installation
    INSTALLATION PROCEDURE 1. INSTALL STEERING PAD SWITCH ASSEMBLY (a) Engage the 2 claws and 2 pins to install the steering pad switch assembly. (b) Install the 2 screws. Torque: 2.4 N·m {24 kgf·cm, 21 in·lbf} (c) Connect the steering pad switch connector to the spiral cable with sensor sub-assembl ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2025 Copyright www.lexusrx.net
    0.0139