Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual: Data List / Active Test

Door Lock Status

Back door condition signal

Unlock or Lock

Unlock: Back door unlocked

Lock: Back door locked

-

Half Latch SW

Half-latch switch signal

OFF or ON

OFF: Back door lock motor in full latch or half latch position

ON: Back door lock motor in open latch position

-

Closer Position SW

Position switch signal

OFF or ON

OFF: Back door lock center gear out of center position (Position switch off)

ON: Back door lock center gear in center position (Position switch on)

-

Pawl Position Switch

Pawl switch signal

OFF or ON

OFF: Back door lock motor except open latched

ON: Back door lock motor open latched

-

Courtesy SW

Back door courtesy switch signal

OFF or ON

OFF: Back door closed

ON: Back door open

-

PBD Touch Sensor (Right)

Power back door sensor assembly RH signal

OFF, ON or Open

OFF: Power back door sensor assembly RH not pressed

ON: Power back door sensor assembly RH pressed

Open: Power back door sensor assembly RH circuit open

-

PBD Touch Sensor (Left)

Power back door sensor assembly LH signal

OFF, ON or Open

OFF: Power back door sensor assembly LH not pressed

ON: Power back door sensor assembly LH pressed

Open: Power back door sensor assembly LH circuit open

-

PBD Main SW

Power back door ON/OFF signal

OFF or ON

Customize setting displayed

-

PBD Close SW

Back door control switch signal

OFF or ON

OFF: Back door control switch not pressed

ON: Back door control switch pressed

-

IG SW

Engine switch signal

OFF or ON

OFF: Engine switch off

ON: Engine switch on (IG)

"OFF" is also displayed for this item when the engine switch is on (ACC).

Close and Lock SW

Door control switch signal

OFF or ON

OFF: Door control switch not pressed

ON: Door control switch pressed

-

PBD Position (3/4-Open)

Load signal detected during back door closing operation (3/4 - Open)

Caution or OK

Caution: Load detected between back door 3/4 and fully open position during back door closing operation

OK: No load detected between back door 3/4 and fully open position during back door closing operation

-

PBD Position (2/4-3/4)

Load signal detected during back door closing operation (2/4 - 3/4)

Caution or OK

Caution: Load detected between back door 2/4 and 3/4 open position during back door closing operation

OK: No load detected between back door 2/4 and 3/4 open position during back door closing operation

-

PBD Position (1/4-2/4)

Load signal detected during back door closing operation (1/4 - 2/4)

Caution or OK

Caution: Load detected between back door 1/4 and 2/4 open position during back door closing operation

OK: No load detected between back door 1/4 and 2/4 open position during back door closing operation

-

PBD Position (Close-1/4)

Load signal detected during back door closing operation (Close - 1/4)

Caution or OK

Caution: Load detected between back door fully closed and 1/4 open position during back door closing operation

OK: No load detected between back door fully closed and 1/4 open position during back door closing operation

-

Closed Position Initialization

Back door fully closed position memorized signal

Not Initialized or Initialized

Not Initialized: Back door fully closed position not memorized

Initialized: Back door fully closed position memorized

-

PBD SW Operation

Back door control switch operation

0.0 s or 0.8 s

Customize setting displayed

-

PBD Buzz In Use

Power back door warning buzzer operation condition signal

OFF or ON

Customize setting displayed

-

PBD Assist Open Operation

Function that enables/disables the power back door assist open operation. When set to ON, the back door will open automatically when the back door opener switch assembly (open switch) is operated.

OFF or ON

Customize setting displayed

-

PBD Assist Close Operation

Function that enables/disables the power back door assist close operation. When set to ON, the back door will close automatically when operated in the close direction manually.

OFF or ON

Customize setting displayed

-

Door Unlock with 1 Motion.

Door or doors to be unlocked when back door locked and power back door operated by pressing transmitter switch

Back Door or ALL DOORS

Customize setting displayed

-

Wireless Power Back Door Open

Function that operates the power back door by pushing the transmitter switch (electrical key transmitter sub-assembly).

Lock:OFF/Unlock:OFF, Lock:OFF/Unlock:ON, Lock:OFF/Unlock:Twice, Lock:OFF/Unlock:0.8s, Lock:Twice/Unlock:Twice or Lock:0.8s/Unlock: 0.8s

Customize setting displayed

-

Power Back Door Opening Adjust

Function that changes the position that the power back door stops during an open operation.

1:Min, 2:Small, 3:Middle, 4:Large or 5:Max

Customize setting displayed

-

Emblem Sensor

Rear emblem sensor assembly connection status*1

Without or With

Without: Rear emblem sensor assembly not connected

With: Rear emblem sensor assembly connected

Not applicable

Emblem Sensor Detection

Rear emblem sensor assembly detection status*1

OFF or ON

OFF: Rear emblem sensor assembly not detecting a hand

ON: Rear emblem sensor assembly detecting a hand

Not applicable

PBD/Emblem Sensor Function

Function that enables/disables the power back door and rear emblem sensor assembly.*1

PBD OFF/Emblem OFF, PBD ON/Emblem OFF or PBD ON/Emblem ON

Customize setting displayed

Not applicable

PBD Buzzer Volume Adjust

Function that changes the volume setting of the power back door warning buzzer.

Small, Middle or Large

Customize setting displayed

-

Emblem Sensor Detection Sensitivity

Function that changes the sensitivity of the rear emblem sensor assembly.*1

Low, Middle or High

Customize setting displayed

Not applicable

Emblem Sensor Sensitivity Reduction Mode Transition Frequency (Frequent Contact/Calibration Failure)

Number of times emblem sensor changed to sensitivity reduction mode (frequent contact/calibration failure)*1

None, Low, Middle or High

None: Never

Low: 1 to 10 times

Middle: 11 to 50 times

High: 51 times or more

Not applicable

Emblem Sensor Sensitivity Reduction Mode Transition Frequency (Power Saving)

Number of times emblem sensor changed to sensitivity reduction mode (power saving)*1

None, Low, Middle or High

None: Never

Low: 1 to 10 times

Middle: 11 to 50 times

High: 51 times or more

Not applicable

Emblem Sensor Sensitivity Drop Frequency (Disturbance Factor)

Number of times emblem sensor sensitivity decreased (wave interference)*1

None, Low, Middle or High

None: Never

Low: 1 to 10 times

Middle: 11 to 50 times

High: 51 times or more

Not applicable

Emblem Sensor Sensitivity Drop Frequency (Foreign Matter Adhering)

Number of times emblem sensor sensitivity decreased (adherence of foreign matter)*1

None, Low, Middle or High

None: Never

Low: 1 to 10 times

Middle: 11 to 50 times

High: 51 times or more

Not applicable

Kick Sensor Connection

Status of the kick door control sensor connection*2

Without or With

Without: kick door control sensor not equipped

With: kick door control sensor equipped

-

Kick Sensor Detection

Status of the kick door control sensor detection*2

OFF or ON

OFF: Kick door control sensor not detecting a foot

ON: Kick door control sensor detecting a foot

-

Kick Sensor Error

Status of the kick door control sensor error*2

Normal or Error

Normal: Kick door control sensor is normal

Error: Kick door control sensor is abnormal

-

Kick Sensor Function

Status of the hands free power back door function*2

OFF or ON

Customize setting displayed

-

Kick Sensor Close & Lock Function

Status of the hands free power back door close and lock function*2

OFF or ON

Customize setting displayed

-

#Codes

Number of DTCs

Min.: 0, Max.: 255

Number of output DTCs

-

Back Door Courtesy SW

Back door courtesy light switch signal*1

OFF or ON

OFF: Back door closed

ON: Back door open

Not applicable

Back Door Open

Back door lock

Permit or Prohibit

Permit: Back door unlocked

Prohibit: Back door locked

-

Back Door Open SW

Power back door switch (integration control and panel assembly) signal

OFF or ON

OFF: Power back door switch (integration control and panel assembly) off

ON: Power back door switch (integration control and panel assembly) on

-

Kick Sensor Operation with ACC ON

Status of the hands free power back door function with engine switch on (ACC).*2

Available or Not Available

Customize setting displayed

-

Tr/B-Door Unlock SW

Back door opener switch assembly (open switch) signal

OFF or ON

OFF: Back door opener switch assembly (open switch) off

ON: Back door opener switch assembly (open switch) on

-

Latch Release

Latch release operation

OFF or ON

-

PBD Open/Close

Power back door motor operation

Forward, Reverse or OFF

-

PBD Buzzer

Power back door warning buzzer sound

OFF or ON

-